Moving a bathtub drain means relocating the drain hole in the tub floor to a new position, usually because you’re installing a new tub or changing the tub’s orientation. This involves cutting the old drain pipe, rerouting it, and patching the old hole. You’ll need basic plumbing tools and some patience, but it’s a manageable DIY project for most homeowners.
What You’ll Need
- Adjustable wrench or basin wrench
- Pipe cutter or hacksaw
- PVC pipe and fittings (if your drain is PVC)
- PVC primer and cement
- Plumber’s putty or silicone sealant
- Patch kit for the old hole (fiberglass or acrylic repair kit)
- Screwdriver
- Bucket and towels
- Safety glasses and gloves
Step-by-Step
- Turn off the water supply. Locate the shut-off valves for the bathtub (usually under the sink or near the tub) and turn them clockwise to close. Also, avoid running water in the house while you work, as the drain line will be open.
- Remove the old drain assembly. Use a screwdriver to remove the drain cover or stopper. Then, use a basin wrench or adjustable wrench to unscrew the drain flange from the drain pipe underneath. If it’s stuck, apply penetrating oil and wait a few minutes.
- Access the drain pipe under the tub. If the tub is on the ground floor with a crawlspace or basement, go underneath. If it’s on a upper floor, you may need to cut an access hole in the ceiling below. Wear safety glasses and a dust mask.
- Cut the old drain pipe. Using a pipe cutter or hacksaw, cut the horizontal drain pipe that connects to the vertical section leading to the tub. Cut a few inches away from the old drain location to leave room for a coupling.
- Remove the old drain pipe section. Unscrew or pull out the remaining pipe from the tub drain hole. You may need to cut it into smaller pieces if it’s long. Clean the area around the cut.
- Patch the old hole in the tub. If the old drain hole is in a different spot, you’ll need to fill it. Clean the area around the hole with acetone. Apply a fiberglass repair kit or a two-part epoxy filler, following the manufacturer’s instructions. Sand it smooth once dry, then refinish with matching tub paint.
- Position the new drain pipe. Measure the distance from the new drain location to the existing horizontal pipe. Cut a new piece of PVC pipe to fit. Dry-fit the pipe and fittings to ensure they align properly.
- Glue the new pipe. Apply PVC primer to the outside of the pipe and inside of the fitting, then apply PVC cement. Push the pipe into the fitting and twist a quarter turn. Hold for a few seconds. Repeat for all joints.
- Connect to the existing drain. Use a coupling to connect the new pipe to the existing horizontal drain. Glue it in place. Ensure the pipe has a slight slope toward the main drain (about a quarter inch per foot) for proper water flow.
- Install the new drain assembly. From above the tub, insert the new drain flange into the new hole. Apply plumber’s putty or silicone sealant around the underside of the flange. From below, thread the drain body onto the flange and tighten with a wrench. Wipe away excess putty.
- Test for leaks. Turn the water supply back on and run water into the tub. Check underneath for any drips. Also pour a bucket of water down the drain to ensure it flows freely.
- Close up access. If you cut an access hole in the ceiling, patch it with drywall and paint. If you worked in a crawlspace, ensure the area is clean.
Common Mistakes
- Not checking the slope. If the new pipe doesn’t slope downward, water will pool and cause clogs.
- Forgetting to patch the old hole properly. A poor patch can lead to leaks or cracks in the tub.
- Using the wrong pipe material. If your drain is metal, you can’t glue PVC directly to it; you’ll need a transition coupling.
- Overtightening the drain flange. This can crack the tub or strip the threads.
- Skipping the primer. PVC cement won’t bond properly without primer.
Tips
- Take photos of the existing plumbing before you start, so you remember the layout.
- Use a level to check the slope of the new pipe.
- If you’re not confident working under the tub, consider hiring a plumber for the drain relocation, as mistakes can cause water damage.
- When patching the old hole, use a piece of backing material (like a small piece of plastic) underneath to support the patch.
- Allow the PVC cement to dry fully before testing.
Troubleshooting
- Water leaks at the new joint. Turn off the water, dry the area, and apply more PVC cement around the joint, or redo the connection with a new coupling.
- Drain is slow. Check for a blockage in the pipe, and verify the slope is correct. If the slope is off, you may need to adjust the pipe hangers.
- The old hole patch cracks. Sand it down, clean it, and apply another layer of epoxy. Let it cure fully before using the tub.
- The drain flange won’t screw on. Make sure the threads are clean and apply plumber’s tape. If it still won’t catch, the flange may be the wrong size.
- You cut the pipe too short. Use a coupling to extend the pipe, or replace the section with a longer piece.
Frequently Asked Questions
Can I move a bathtub drain without cutting the floor? In most cases, you need access to the underside of the tub. If there’s no crawlspace or basement, you may need to cut an access panel in the ceiling below.
Do I need a permit to move a bathtub drain? Many local building codes require a permit for plumbing changes. Check with your local building department before starting.
How long does it take to move a bathtub drain? For a simple relocation, expect to spend a few hours. If you need to patch drywall or deal with difficult access, it could take a full day.
Can I use flexible pipe for the drain? Flexible drain pipes are generally not recommended for bathtubs because they can sag and trap debris. Use rigid PVC or ABS pipe for a reliable drain.
What if my tub is cast iron? Patching a hole in cast iron is more difficult. You may need to use a special epoxy or consider replacing the tub.
Is it easier to move the drain or the tub? If the tub is being replaced, it’s often easier to choose a tub with a drain location that matches your existing plumbing. Moving the drain is only necessary if you’re set on a specific tub or layout.