Making a saddle for a rocking horse lets you match the saddle to your horse’s size and your child’s comfort, and it is a satisfying woodworking and leathercraft project. You will create a secure, comfortable seat that looks great and holds up to years of rocking. Before you start, gather your materials and take careful measurements of your horse’s back.
What You’ll Need
- Leather or heavy fabric (about 2 square feet for a small horse, more for larger)
- Sturdy thread (waxed polyester or nylon)
- Leather needle (if sewing by hand) or a sewing machine with a leather needle
- Sharp scissors or a rotary cutter
- Measuring tape
- Marker or chalk for tracing
- Awl or hole punch
- Strap material (for girth and cinch)
- Buckles or heavy-duty snaps
- Stuffing (polyester fiberfill or foam) for padding
- Optional: rivets and a rivet setter, edge beveler, and leather conditioner
Step-by-Step
- Measure your horse’s back. Use a flexible measuring tape to measure from the front of the saddle area (just behind the horse’s neck) to the back (where the saddle should end, before the hips). Also measure the width across the back at the front and back of that area. Write these numbers down.
- Create a paper template. On a piece of paper, draw a shape that is roughly oval, with a slight curve to fit the horse’s back. The front should be a bit narrower than the back. Add an extra inch all around for seam allowance. Cut out the template and hold it against the horse to check the fit. Adjust as needed.
- Cut your leather or fabric. Place the template on your material and trace around it with chalk. Cut out two identical pieces: one for the top of the saddle and one for the bottom. If you want a padded saddle, also cut a piece of foam or batting the same shape but slightly smaller.
- Add padding (optional). If you are using foam, place it between the two leather pieces. If you are using loose stuffing, you will add it later. For a firmer saddle, you can glue the foam to the bottom piece before sewing.
- Mark and punch holes. If you are sewing by hand, use an awl or hole punch to make holes around the edge of both pieces, about a quarter-inch from the edge and a half-inch apart. If using a sewing machine, you can skip this step.
- Sew the pieces together. Place the two pieces with their right sides facing each other (if your material has a right side). Sew around the edge, leaving a gap of about four inches on one side for turning. If you are using foam, make sure it is inside before you close the gap. If using loose stuffing, leave the gap open.
- Turn the saddle right side out. Carefully pull the material through the gap so the right side is facing out. Use a blunt tool, like a chopstick, to push out the corners gently.
- Stuff the saddle (if needed). If you are using loose stuffing, fill the saddle through the gap until it is firm but not overstuffed. Then hand-sew the gap closed with a ladder stitch or whip stitch.
- Attach the girth and cinch straps. Cut two straps long enough to go under the horse’s belly. One should be positioned near the front of the saddle, the other near the back. You can sew or rivet these straps to the bottom of the saddle. Make sure they are centered and will sit flat against the horse.
- Add buckles or snaps. Attach a buckle or heavy-duty snap to one end of each strap so you can fasten the saddle securely. Test the fit on the horse, adjusting the strap length as needed.
- Finish and condition. If using leather, apply a leather conditioner to keep it supple. If using fabric, you may want to add a waterproofing spray. Check all stitching and hardware for security.
Common Mistakes
- Measuring incorrectly. A saddle that is too small will pinch, and one that is too large will slide. Always measure twice and make a paper template first.
- Using weak thread. Regular cotton thread will break under the strain of a rocking child. Use waxed polyester or nylon.
- Skipping the padding. A saddle without padding is uncomfortable for the rider and can rub the horse’s finish. Even a thin layer of foam makes a big difference.
- Attaching straps too far apart. If the girth straps are too far apart, they may not hold the saddle snugly. Position them so they sit just behind the front legs and just in front of the back legs.
- Overstuffing. Too much stuffing makes the saddle lumpy and hard to sit on. Aim for a firm, even shape.
Tips
- Use a leather punch to make clean holes for hand sewing; it makes the process much easier.
- If you are new to leatherwork, practice on scrap pieces first.
- For a child who will ride often, consider adding a small pommel at the front of the saddle to help them hold on.
- You can decorate the saddle with stitching, conchos, or paint, but keep embellishments flat so they don’t cause discomfort.
- If your horse has a prominent withers, add extra padding in that area to prevent rubbing.
Troubleshooting
- The saddle slides forward. This usually means the back strap is too loose. Tighten the girth and cinch, or add a breastplate (a strap that goes around the horse’s chest) to keep it in place.
- The saddle is too tight. If the saddle leaves marks on the horse or is hard to fasten, you may have cut it too small. Remake it with a larger template, or add a leather shim under the straps.
- The stitching is breaking. This is likely because the thread is too thin or the needle is dull. Use a heavier thread and a new leather needle, and make sure your holes are not too close to the edge.
- The stuffing is lumpy. If you used loose stuffing, try to distribute it evenly. If it is still lumpy, remove it and use a single piece of foam instead.
- The horse’s paint gets scratched. Add a soft lining, like felt or fleece, to the underside of the saddle. This will protect the horse’s finish and reduce slipping.
Frequently Asked Questions
- What type of leather is best? Vegetable-tanned leather is easy to tool and dye, but it is stiff. Chrome-tanned leather is softer and more flexible, which may be easier for a beginner. For a rocking horse, a medium-weight leather (about 3-4 ounce) works well.
- Can I use fabric instead of leather? Yes, heavy canvas or denim can work, but it will not be as durable. If you use fabric, reinforce the stitching and consider adding a leather or vinyl trim to prevent fraying.
- How do I know the saddle is safe for my child? Ensure all straps are securely fastened and there are no sharp edges or loose parts. The saddle should sit flat and not shift when the horse rocks. Always supervise young children while they ride.
- Do I need to use a pattern? No, but a paper template is essential for getting the shape right. You can make your own by tracing the horse’s back, or you can find free patterns online (but you will need to adjust them to your horse’s measurements).
- How do I clean the saddle? For leather, wipe with a damp cloth and use a leather cleaner occasionally. For fabric, spot clean with mild soap and water. Avoid soaking the saddle, as it can damage the stuffing.
- Can I add stirrups? Yes, you can attach stirrup straps to the front of the saddle. Make sure they are adjustable and that the stirrups are not too long for the child’s legs.