Coating a silk screen with photo emulsion is the essential first step in creating a stencil for screen printing. A properly coated screen ensures crisp, durable prints and makes the exposure and washing-out process much smoother. Before you begin, you need a clean, dry screen, a scoop coater, and a dark room or a low-light area, as photo emulsion is light-sensitive.
What You’ll Need
- Silk screen (mesh stretched on a frame)
- Photo emulsion (liquid, light-sensitive)
- Scoop coater (a trough that holds the emulsion)
- Masking tape (to protect the frame edges)
- Degreaser or mild dish soap
- Water spray bottle
- Drying rack or a dark, dust-free area
- Gloves and safety glasses
Step-by-Step
- Prepare your workspace. Work in a room with low or yellow light, away from direct sunlight. Cover the work surface with newspaper or a drop cloth. Have all your supplies within reach.
- Clean the screen thoroughly. Use a degreaser or mild dish soap and warm water to scrub both sides of the mesh. Rinse well and let it dry completely. Any grease or dust will prevent the emulsion from adhering properly.
- Protect the frame edges. Apply masking tape to the inside edges of the frame where it meets the mesh. This prevents emulsion from building up in the corners, which can cause uneven coating and make reclaiming harder.
- Pour emulsion into the scoop coater. Fill the trough about halfway, or according to the manufacturer’s instructions. Do not overfill, as it will spill and create bubbles.
- Hold the screen at a slight angle. Lean the screen against a wall or hold it upright with one hand. The mesh should be vertical, and you’ll coat from the bottom edge upward.
- Apply the first coat. Place the scoop coater at the bottom edge of the screen, with the trough’s lip touching the mesh. Tilt the coater so the emulsion makes contact with the mesh. Push the coater upward in one smooth, steady motion. You should see a thin, even layer of emulsion on the mesh.
- Apply the second coat (optional but recommended). For a thicker stencil, repeat the same motion from the bottom to the top, but this time coat the opposite side of the screen (the outside). This helps fill the mesh openings and creates a more durable stencil.
- Check for even coverage. Hold the screen up to a light source (low light) and look for any thin spots or missed areas. If you see any, apply another thin coat to those specific spots.
- Dry the screen flat. Lay the screen flat with the coated side facing up (or down, depending on your drying rack design). Place it in a dark, dust-free area. Let it dry completely, which can take a few hours or overnight, depending on humidity and emulsion type.
- Store coated screens properly. Once dry, keep the screen in a light-proof bag or box until you are ready to expose it. Exposure to light before exposure will ruin the emulsion.
Common Mistakes
- Coating in bright light. Even brief exposure to sunlight or strong indoor light can prematurely harden the emulsion, making it impossible to wash out your design.
- Uneven pressure on the scoop coater. Pressing harder on one side than the other results in an uneven coating, which can cause thin spots or over-thick areas.
- Coating a dirty screen. Grease, dust, or old ink residue will cause the emulsion to peel or not adhere, leading to pinholes in your stencil.
- Applying too many coats. While a thicker stencil is good for long runs, too many coats can make it difficult to wash out fine details. Two coats are usually sufficient for most jobs.
- Skipping the drying step. Coating a second side before the first is dry can trap moisture and create an uneven surface. Always let the first coat dry before adding another.
Tips
- Use a scoop coater that matches your mesh. A coater that is too small will leave uneven edges; one that is too large can be awkward to handle. Choose one that is slightly smaller than the inside width of your frame.
- Work in a warm, dry room. Emulsion dries faster in a warm, dry environment, which reduces the chance of dust settling on the wet surface.
- Keep a wet edge. When coating, try to keep a continuous bead of emulsion at the edge of the coater. This helps achieve a smooth, even coat.
- Use a fan (low speed) to speed up drying. A gentle fan can help dry the screen faster, but make sure it doesn’t blow dust onto the wet emulsion.
- Label your screens. If you coat multiple screens, label them with the date and mesh count so you know which is which.
Troubleshooting
- Emulsion is peeling off. This usually means the screen wasn’t cleaned properly or the emulsion was applied too thick. Reclaim the screen, clean it thoroughly, and re-coat with a thinner layer.
- Pinholes appear after washing out. Pinholes are caused by dust or grease on the mesh, or by air bubbles in the emulsion. Ensure the screen is spotless, and when pouring emulsion, let it settle to avoid bubbles.
- The stencil is too thin or washes out too easily. You may have applied too thin a coat or not enough coats. Add another coat on the outside and let it dry fully before exposing.
- The stencil is too thick and won’t wash out. This happens when you apply too many coats or the emulsion is over-exposed. You may need to reclaim the screen and start over, using fewer coats and a shorter exposure time.
- Emulsion is drying on the scoop coater. Clean the coater immediately after each use with water. If emulsion dries on it, it can chip off and contaminate the next coating.
- Uneven coating on the mesh. This is often due to jerky motion or inconsistent pressure. Practice smooth, steady strokes, and consider using a coater with a rounded edge for better control.
Frequently Asked Questions
- How many coats of emulsion should I use? For most standard screen printing, two coats are recommended: one on the inside and one on the outside. For very fine details, one coat may be enough; for heavy ink deposits, you might add a third coat.
- How long does the emulsion take to dry? Drying time varies with humidity and emulsion type, but it typically takes a few hours to overnight. You can test by touching the mesh in a corner; it should feel completely dry and not tacky.
- Can I coat a screen in normal room light? No, normal room light contains UV rays that can start to harden the emulsion. Use a dark room with only a safelight (yellow or red) or work in very dim conditions.
- What is the shelf life of photo emulsion? Unopened emulsion can last for months or even a year if stored in a cool, dark place. Once opened, it’s best to use it within a few months, as it will slowly become less sensitive.
- Do I need to coat both sides of the screen? Coating both sides is a common practice to ensure the mesh is fully filled and the stencil is durable. However, some printers only coat the outside (the side that will contact the substrate) and get good results.
- Can I reuse a coated screen after printing? Yes, you can reclaim the screen by washing out the emulsion with a special remover solution, then cleaning and re-coating it. This is a standard practice and can be done many times.