How to Cover Outside House Vents

Covering the outside vents around your house can help keep out pests, debris, and cold drafts, and it can also improve the look of your home’s exterior. Before you start, take a moment to identify the types of vents you have—foundation vents, dryer vents, bathroom exhaust vents, and intake vents all have different needs. You’ll also want to check local building codes, as some areas require vents to remain open for proper airflow. This guide will walk you through the process safely and effectively.

What You’ll Need

  • Measuring tape
  • Screwdriver or drill
  • Screws or masonry anchors (depending on your vent material)
  • Vent covers or grilles (choose the right size and type for each vent)
  • Caulk and caulking gun (for sealing gaps)
  • Utility knife
  • Safety glasses and work gloves
  • Ladder (if vents are above ground level)
  • Wire mesh or hardware cloth (for pest-proofing)

Step-by-Step

  1. Identify each vent’s purpose. Walk around your house and note every outside vent. Common ones include foundation vents (for crawl space airflow), dryer exhaust vents, bathroom and kitchen exhaust vents, and attic intake vents. Never block a vent that is essential for combustion appliances (like a furnace or water heater) or for drying clothes—this can cause dangerous backdrafting or fire hazards.
  2. Measure the vent openings. Use a measuring tape to get the width and height of each vent. Write down the measurements so you can buy covers that fit properly. For round vents, measure the diameter.
  3. Choose the right cover. For foundation vents, you can use louvered or mesh covers that allow airflow while blocking pests. For dryer vents, use a cover with a flap that opens only when the dryer is running—never use a solid cover, as it will trap lint and moisture. For bathroom and kitchen exhaust vents, use a cover with a backdraft damper. For intake vents, you might use a decorative grille that still allows air in.
  4. Prepare the surface. Clean the area around the vent with a brush or cloth to remove dirt, cobwebs, and loose paint. If the vent is painted, you may need to scrape away peeling paint to get a good seal.
  5. Install the cover. Hold the cover up to the vent and mark the screw holes. If the vent is made of wood or vinyl, you can screw directly into it. If it’s masonry (brick or concrete), you’ll need to use masonry anchors—drill pilot holes, insert the anchors, then screw the cover in place. Make sure the cover is level and snug.
  6. Seal gaps. Apply a bead of caulk around the edges of the cover to seal any gaps where air or pests could enter. Smooth the caulk with your finger or a caulking tool. Let it dry according to the manufacturer’s instructions.
  7. Add pest-proofing if needed. If you’re covering a vent with a mesh cover, ensure the mesh is fine enough to keep out mice and insects—typically hardware cloth with a small grid. If the cover doesn’t have built-in mesh, you can attach a piece of hardware cloth to the back with screws or staples.
  8. Test the airflow. After installation, check that air can still flow through the vent. For dryer vents, run the dryer briefly and confirm the flap opens. For exhaust vents, turn on the bathroom fan and feel for airflow at the outside vent. If airflow is blocked, remove the cover and adjust.

Common Mistakes

  • Blocking essential vents. The biggest mistake is covering a vent that needs to stay open, like a combustion air intake or a dryer vent. This can lead to carbon monoxide buildup, fire risk, or moisture damage.
  • Using the wrong cover type. A solid cover on a dryer vent is a fire hazard. A cover without a damper on a bathroom exhaust can let cold air in and cause condensation.
  • Poor sealing. Leaving gaps around the cover lets in pests and drafts, defeating the purpose.
  • Ignoring local codes. Some areas have building codes that require certain vents to remain open or have specific clearances. Check with your local building department before making changes.
  • Overtightening screws. This can crack the vent frame or strip the holes, especially on plastic or thin metal.

Tips

  • For foundation vents, consider using covers with built-in screens that you can remove for cleaning.
  • If you live in a cold climate, look for covers with insulated flaps to reduce drafts.
  • Use stainless steel screws for exterior applications to prevent rust.
  • If you’re painting the cover, do it before installation to avoid getting paint on the wall.
  • Take a photo of each vent before covering it—this helps you remember which cover goes where if you need to remove them later.
  • Check the covers seasonally to make sure they haven’t come loose or been damaged by weather.

Troubleshooting

  • Cover doesn’t fit. If the cover is too small or too large, double-check your measurements. You can use a vent extender or trim the cover with a utility knife if it’s slightly oversized. For a better fit, look for adjustable covers or custom sizes.
  • Screws won’t hold. If the screw holes are stripped, use a larger screw or a wall anchor. For masonry, make sure you’re using the correct anchor type and that the pilot hole is the right size.
  • Airflow seems restricted. If you notice reduced airflow after installation, the cover may be too restrictive. Switch to a cover with larger louvers or a more open mesh. For dryer vents, clean the lint from the duct first—a clogged duct is often the real issue.
  • Water leaks around the cover. This usually means the caulk seal failed or the cover isn’t sloped to shed water. Remove the cover, clean the area, reapply caulk, and make sure the top edge of the cover is slightly tilted outward.
  • Pests still getting in. If you see signs of insects or rodents, the mesh may be too large or there may be gaps elsewhere. Replace with finer mesh and seal all edges with caulk or expanding foam.

Frequently Asked Questions

Can I cover all my vents completely? No. Only cover vents that are safe to block, like unused foundation vents in some cases, but even those often need to remain open for ventilation. Never block dryer vents, combustion air intakes, or vents that serve appliances.

What is the best material for vent covers? Aluminum and galvanized steel are durable and rust-resistant. Plastic covers are cheaper but may crack in extreme cold. Choose a material that matches your home’s exterior and climate.

Do I need to remove the cover in winter? It depends on the vent. For dryer vents, the cover should always be in place. For foundation vents, some people close them in winter to reduce heat loss, but this can trap moisture—check with a local expert. For exhaust vents, keep them open year-round.

How do I know if a vent is for combustion? Combustion vents are typically located near furnaces, water heaters, or fireplaces. They may have a metal duct and are often labeled. If you’re unsure, have a professional inspect your home.

Will covering vents increase my energy efficiency? It can help reduce drafts, but blocking essential vents can cause moisture problems or safety issues. Properly sealing around vents with caulk and using insulated covers on non-essential vents is a safer way to improve efficiency.

How often should I replace vent covers? Most covers last for years, but check them annually for rust, cracks, or loose screws. Replace them if they are damaged or no longer seal properly.