Yes, you can build your own tiered stone fountain, and it is a manageable weekend project for most homeowners. The key is choosing the right pump, sealing the stone properly, and understanding how water flows from tier to tier before you start stacking.
Why Build a Tiered Stone Fountain?
A tiered stone fountain adds a natural, calming focal point to a garden, patio, or entryway. Unlike a pre-formed plastic fountain, a stone version blends with landscaping and ages gracefully. Building it yourself saves money and lets you customize the size, stone type, and overall look. It also gives you control over the pump size and water flow, which is often the weak point of cheaper store-bought fountains.
How a Tiered Fountain Works
The basic principle is simple: a pump sits in a basin at the bottom, pushes water up through a tube to the top tier, and the water spills over the edge of each tier down to the next. The pump must have enough lift (measured in feet of head) to push water to the highest tier, and the basin must hold enough water to keep the pump submerged at all times. A common mistake is buying a pump that is too weak, resulting in a trickle instead of a cascade. The water level in the basin will drop as it coats the stone and evaporates, so you need to check and refill it regularly, especially in hot, dry weather.
Choosing Your Stone and Design
The most popular choices are flagstone, slate, river rock, and granite. Flagstone and slate are easier to drill and shape, while granite is heavier and more durable but harder to work with. You can use a pre-drilled stone kit, which simplifies the process, or drill your own holes with a masonry bit. When selecting stones, consider the diameter of each tier—each upper tier should be smaller than the one below it so water falls freely. A typical design uses three tiers, but you can use more if you have a strong pump. Also, think about the overall height: a fountain that is too tall may require a larger pump and a more stable base.
Step-by-Step Construction
Here is a general outline of the process. Always follow the specific instructions for your pump and any sealant you use.
- Plan the layout: Decide on the location and the number of tiers. Make sure the ground is level.
- Set the basin: Use a large, watertight container (like a plastic tub or a pre-formed pond liner) buried or placed on the ground. It must be big enough to hold several gallons of water.
- Install the pump: Place the pump in the basin, and run the tubing up through the center of your stone stack. The tube should be long enough to reach the top tier.
- Drill holes: If your stones are not pre-drilled, drill a hole through the center of each tier, slightly larger than your tubing. Use a hammer drill with a masonry bit and keep the stone wet to prevent overheating.
- Stack the tiers: Thread the tubing through each stone, starting with the largest at the bottom. Use a level to ensure each tier is flat. You can use small shims (like pebbles) to level a stone if needed.
- Seal the joints: Apply a waterproof sealant (designed for stone and outdoor use) around the hole on the top of each tier to prevent water from seeping down the outside of the tube. Also seal any cracks in the stone that could leak.
- Connect the top: Attach the tubing to the top tier, either by letting it flow out of the hole or by attaching a small fountain head. The water should spill evenly over the edge.
- Test and adjust: Fill the basin with water, plug in the pump, and watch the flow. Adjust the pump’s flow rate (if it has a dial) to get a pleasing cascade without splashing.
Common Problems and Fixes
One of the most frequent issues is water leaking from the base or between tiers. This is usually due to an incomplete seal. Reapply sealant to any joint that weeps. Another problem is the pump running dry because the water level drops too low. Always keep the pump submerged; you can add a float valve to automatically top up the basin. Algae growth is also common in outdoor fountains. To minimize it, keep the fountain out of direct sunlight if possible, and clean the basin and pump regularly. A mild bleach solution (a small amount in a large basin) can help, but be sure to rinse thoroughly before running the pump again, and never use bleach if you have fish or plants in the water.
Costs and Materials
The cost of a DIY stone fountain varies widely depending on the stone. A basic kit with pre-drilled stones and a pump can be quite affordable, while large, natural granite slabs can be expensive. You will also need a pump (choose one rated for fountains or ponds), tubing, a basin, sealant, and possibly a drill bit. In most cases, building your own is still cheaper than buying a comparable pre-made stone fountain from a garden center. You can often find used or reclaimed stone at landscaping supply yards, which can reduce costs significantly.
Safety and Maintenance Tips
Electrical safety is paramount. Use a pump that is rated for outdoor use and is plugged into a Ground Fault Circuit Interrupter (GFCI) outlet. Keep all electrical connections dry and off the ground. If you have small children or pets, consider a fountain with a shallow basin or a cover over the pump to prevent accidents. Regular maintenance includes cleaning the pump filter every few weeks, checking the water level daily during hot weather, and draining and storing the pump indoors before winter if you live in a freezing climate. Stone can crack if water freezes inside it, so it is best to disassemble and store the stones or cover the fountain during the off-season.
Alternatives to a Stone Fountain
If a stone fountain feels too heavy or permanent, consider a ceramic or resin tiered fountain, which is lighter and easier to move. A simple pump and a single large stone bowl can also create a minimalist water feature. For a more natural look, you could build a rock waterfall with a pond liner, which uses similar principles but on a larger scale. Each option has its own maintenance needs, so choose based on your space, budget, and how much effort you want to put into upkeep.
Frequently Asked Questions
What size pump do I need? The pump should be able to lift water to the height of your top tier. As a rule of thumb, choose a pump that can move at least a few hundred gallons per hour for a small to medium fountain. Check the pump’s specifications for the flow rate at the height you need.
How do I keep the water from turning green? Algae thrives in sunlight and stagnant water. Keep your fountain shaded if possible, and clean it regularly. You can also add a small amount of aquatic plant-safe algaecide, but always follow the product’s instructions.
Can I use any stone? Not all stones are safe. Avoid soft stones like sandstone or limestone, which can dissolve in water. Hard stones like granite, slate, and basalt are better choices. Also, make sure the stone is not painted or treated with chemicals that could leach into the water.
Do I need to seal the stone? Yes, sealing the stone and the joints helps prevent leaks and reduces mineral buildup. Use a sealant specifically designed for outdoor stone and water features. Reapply it every year or two, depending on the product.
How often do I need to refill the water? It depends on the weather and the fountain’s design. In hot, dry conditions, you may need to add water every day or two. In cooler weather, once a week may be enough. Always keep the pump submerged.
Can I build a fountain without a pump? No, a pump is essential for circulating the water. Without it, you would have a stagnant pool, which attracts mosquitoes and becomes unhealthy. A solar pump is a good option if you don’t have an outdoor outlet.