Tree string art is a craft where you wrap colorful thread or string around nails or pegs arranged in the shape of a tree on a wooden board. It creates a textured, dimensional picture that looks like a stylized tree with a trunk and a full canopy of leaves. The result is a popular wall decoration that combines geometry with a natural, handmade look.
What Makes Tree String Art Different
Unlike flat drawings or paintings, string art builds the image from physical lines of thread stretched between points. The tree shape emerges from the negative space—the areas where string is absent—as well as from the density of the wrapped threads. A typical tree design has a straight or slightly curved trunk made of parallel vertical strings, and a round or triangular canopy filled with radiating lines that cross each other at many angles.
The effect is both graphic and airy. From a distance, the canopy looks solid; up close, you see individual strands and the play of light on the thread. This dual appearance is why the craft has remained popular for decades, and why tree designs in particular are so common—they are simple enough for beginners but offer room for creativity in color and pattern.
How Tree String Art Is Made
The basic process is straightforward and requires only a few tools. You start with a wooden board, a printed or drawn tree template, small nails or pins, a hammer, and thread or embroidery floss. The steps are:
- Sand the board lightly and apply a finish or paint if you want a colored background.
- Place the template on the board and mark the outline of the tree with a pencil.
- Hammer nails along the outline of the trunk and the canopy, spacing them evenly—usually about half an inch apart.
- Remove the paper template carefully.
- Tie the thread to one nail and begin wrapping it around the nails to fill in the trunk and canopy.
- For the trunk, wrap the string back and forth between the two sides in a zigzag or parallel pattern.
- For the canopy, wrap the string across the circle in many directions, rotating the board as you go, until the density looks right.
- Tie off the thread on a nail and trim the end.
The key is to keep the tension even so the string doesn’t loosen or pull the nails out. Most crafters use a simple over-and-under wrapping motion, but you can also create patterns like spirals or weaves.
Choosing the Right Materials
The board is the foundation. Pine or plywood works well because it is soft enough to accept nails easily but sturdy enough to hold them. A board that is at least a quarter-inch thick prevents nails from poking through the back. The size of the board determines the scale of your tree; a small board might be a few inches across, while a large piece can be several feet wide.
Nails should be small—about half an inch long—with a flat head so the string doesn’t slip off. You can buy packs of finishing nails at most hardware stores. The string is the most visible element, so choose a color that contrasts with the board. Embroidery floss is a common choice because it is thin and comes in many colors, but you can also use crochet thread, yarn, or even fishing line for a subtle effect.
For a more polished look, some crafters paint the board before adding nails, or they use a dark stain to make the thread pop. Others leave the wood natural for a rustic feel. The choice of background color dramatically changes the mood of the piece.
Common Mistakes and How to Avoid Them
One frequent error is hammering nails at uneven depths, which makes the string look wavy. Try to drive each nail to the same height, or use a pair of pliers to hold the nail and tap gently. Another issue is using too much string in the canopy, which can obscure the tree shape. Start with a light fill and add more only if needed.
Beginners often struggle with the trunk—if you wrap the string too tightly, it can bend the nails inward. Keep the tension moderate and wrap in a figure-eight pattern to distribute the force. Also, be careful when removing the paper template; if you pull too hard, you might dislodge nails. Tear the paper away in small pieces instead.
Finally, don’t forget to seal the back of the board with a felt pad or picture hanger before hanging, so the nails don’t scratch the wall.
Cost and Time to Make One
Tree string art is an inexpensive project. A small board, a pack of nails, and a spool of thread can cost only a few dollars total, especially if you already have a hammer at home. Larger boards and higher-quality thread will raise the price, but even a substantial piece rarely costs more than a modest craft supply purchase.
The time required depends on the size and complexity. A simple tree on a small board can be finished in a couple of hours, while a large, densely filled canopy might take several evenings. The wrapping process is repetitive and can be relaxing, but it does require patience to achieve an even look.
Alternatives and Variations
If you don’t want to hammer nails, you can use a foam board and push pins instead, which is safer for children and easier to correct. Another variation is to use colored yarn for a chunkier, more textured tree, or to add beads to the string for a decorative touch.
You can also create a tree silhouette without a trunk, using only the canopy, or make a family tree with names written on small tags attached to the branches. Some crafters add a moon or stars in the background by using different colored nails or by wrapping a separate section of the board. The basic technique stays the same, but the design possibilities are nearly endless.
Frequently Asked Questions
How do I keep the string from slipping off the nails? Use nails with a wide, flat head and wrap the string around the nail at least twice. Also, keep the tension tight enough to hold the string in place but not so tight that it pulls the nail out.
Can I use a pre-made kit? Yes, many craft stores sell kits that include a pre-drilled board, nails, and thread. These are great for beginners because they take the guesswork out of spacing and design.
What is the best way to hang tree string art? Attach a picture hanger or sawtooth hanger to the back of the board, centered near the top. For heavier boards, use two hangers spaced apart to keep it level.
How do I clean string art? Dust it gently with a soft brush or a dry microfiber cloth. Avoid using water or cleaning sprays, as they can stain the wood or damage the thread.
Can I make a tree string art without a template? Yes, you can draw the tree freehand directly on the board. If you’re not confident, you can project an image onto the board and trace it, or use a printed template and transfer it with carbon paper.