Yes, you can screw a curtain rod through plaster, but you must use the correct anchors and technique, as plaster is brittle and will crack if you drive a screw directly into it. The safest approach is to drill a pilot hole and use a specialized plaster anchor or a toggle bolt to distribute the weight.
Why Plaster Is Different From Drywall
Plaster walls are common in older homes and are made of a hard, brittle plaster layer applied over a lath backing (wood strips) or, in some cases, directly over masonry. Unlike drywall, which is a soft gypsum core sandwiched between paper, plaster has no give. When you drill into it, the drill bit can grab and pull, causing the plaster to crack or crumble around the hole.
Another key difference is thickness. Plaster is typically only about a half-inch to three-quarters of an inch thick, and behind it is either a hollow cavity (over lath) or a solid material (over masonry). This affects which anchor type you can use. A standard drywall anchor relies on the soft core to expand and grip; in plaster, the hard surface can prevent the anchor from expanding properly, or the expansion can crack the plaster.
How to Choose the Right Anchor
The right anchor depends on the weight of your curtain rod and the wall’s construction. For a lightweight rod with sheer curtains, a simple plastic expansion anchor might work, but for heavier drapes, you need something stronger.
- Plastic expansion anchors: Best for very light loads, under a few pounds. They require a precise pilot hole and can crack plaster if over-tightened.
- Threaded drywall anchors (self-drilling): These are designed for drywall, not plaster. The sharp threads can cause spalling (chipping) in plaster. Avoid them unless the plaster is very thick and you pre-drill.
- Toggle bolts: The most reliable choice for hollow plaster walls. The spring-loaded wings open behind the wall, spreading the load over a large area. They work well with lath-and-plaster because the wings catch on the lath or the back of the plaster.
- Molly bolts (hollow-wall anchors): These are metal sleeves that expand as you tighten the screw. They are excellent for plaster because the sleeve grips the back of the plaster, not just the surface. They are a bit more work to install but are very sturdy.
- Masonry anchors: For plaster over concrete or brick, use a masonry anchor (like a sleeve anchor) and a hammer drill. These do not rely on a hollow cavity.
Step-by-Step Installation Without Cracking
Before you start, locate the studs or lath behind the plaster. A stud finder can help, but many older homes have metal lath that confuses standard finders. You can also tap the wall and listen for a solid sound (stud) versus a hollow sound (cavity).
- Mark your holes with a pencil, using a level to keep the rod straight.
- Tape over the mark with painter’s tape. This reduces surface chipping when the drill bit enters.
- Drill a pilot hole using a masonry bit (carbide-tipped) for plaster. Start slowly and do not push hard. The bit should be slightly smaller than the anchor’s diameter.
- Insert the anchor according to its type. For a toggle bolt, push the wings through the hole and pull back to set them. For a molly bolt, tap it in and then tighten the screw to expand the sleeve.
- Attach the bracket and screw in the rod. Do not overtighten; stop when the bracket is snug against the wall.
Common Problems and How to Avoid Them
The most frequent issue is a large crater forming around the screw. This happens when the drill bit is too large or when you use a hammer to tap in an anchor that is too big. Another problem is the anchor spinning in the hole, which occurs when the pilot hole is too large for the anchor.
If you hit a lath (the wood strip behind the plaster), you are in luck. You can screw directly into the lath without an anchor, as long as the screw is long enough to bite into the wood. However, you must still drill a pilot hole to avoid splitting the lath and cracking the plaster.
If you are hanging a heavy rod, consider installing a wooden cleat or a decorative shelf bracket that spans two studs. This spreads the weight and avoids relying on a single anchor point.
Comparison: Toggle Bolts vs. Molly Bolts vs. Screws
For a typical curtain rod, toggle bolts are often the easiest for a beginner because they do not require precise depth. Molly bolts are sturdier for medium-to-heavy loads but require you to pull the screw out after setting the sleeve, which can be fiddly. Plain screws into lath are the strongest if you hit a stud, but the location of studs rarely aligns with where you want the rod.
In terms of removal, toggle bolts leave a large hole when removed, while molly bolts leave a smaller one that can be patched more easily. If you are renting, consider using a tension rod instead of drilling at all.
Alternatives to Drilling Into Plaster
If you want to avoid the risk of cracking, there are several non-invasive options. Tension rods fit inside the window frame and require no holes. For heavier curtains, a ceiling-mounted rod that screws into the ceiling joist is an option, though it changes the look. Adhesive hooks are not strong enough for most curtain rods, but they can hold lightweight valances.
Another alternative is to use a magnetic rod if you have metal window frames, but this is limited to very light curtains.
Safety and Long-Term Care
Always wear safety glasses when drilling into plaster, as the dust is fine and can irritate eyes. The dust from old plaster may contain silica, so wear a dust mask and ventilate the room. After installation, check the brackets for tightness after a few weeks, as plaster can compress slightly over time.
If a screw pulls out, do not just move the bracket an inch over and try again. Patch the hole with a plaster repair compound, let it dry, sand it smooth, and re-drill in a new spot at least a couple of inches away from the damaged area.
Frequently Asked Questions
Will a regular drywall screw work in plaster? No. A drywall screw has coarse threads that will tear the plaster. You need a fine-thread screw or an anchor designed for masonry or plaster.
How do I know if my wall is plaster or drywall? Knock on it. Plaster sounds solid and dull, while drywall sounds hollow. You can also look at the texture; plaster often has a smoother, harder surface, and drywall has a paper face that is easy to dent with a thumbtack.
Can I use a hammer drill on plaster? Yes, but only if the plaster is over masonry. For plaster over wood lath, a regular drill with a masonry bit is fine. A hammer drill can cause excessive vibration and crack the plaster.
What size pilot hole should I drill? It depends on the anchor. The anchor packaging usually lists the recommended drill bit size. If you do not have the package, use a bit that is slightly smaller than the anchor’s body diameter, not the threads.
What if my curtain rod is very heavy? Use multiple brackets (at least three) and attach each bracket with a toggle bolt. Alternatively, mount a wooden board across two studs and attach the brackets to the board.
Can I screw directly into the lath? Yes, if you hit a lath strip. Use a wood screw that is at least an inch long and drill a pilot hole first. The lath is usually about an inch wide, so you have a small target.