Replacing an entry door improves security, energy efficiency, and curb appeal. This guide covers the full process, from removing the old door to installing the new one, with practical tips to avoid common pitfalls.
What You’ll Need
- New prehung entry door (correct size and swing)
- Shims (wood or composite)
- Level (at least 2 feet long)
- Tape measure
- Screwdriver or drill/driver
- Pry bar and hammer
- Utility knife
- Caulk and caulk gun
- Expanding foam insulation (low-pressure, door/window type)
- Screws (long, for door frame anchoring)
- Safety glasses and work gloves
- Optional: reciprocating saw for cutting old nails
Step-by-Step
- Measure the rough opening. Before buying a new door, measure the width and height of the existing door frame from the inside of the framing studs (not the trim). Also measure the depth of the wall. Most prehung doors come in standard sizes, but you need to match the rough opening.
- Remove the interior and exterior trim. Use a pry bar to gently remove the casing (trim) around the door on both sides. Slide the pry bar under the trim and work it loose, being careful not to damage the wall. If you plan to reuse the trim, set it aside.
- Disconnect the door from the frame. If you are replacing the entire prehung unit, you can skip this step. But if you are only replacing the slab (the door itself), remove the hinge pins by tapping them out with a screwdriver and hammer. Then lift the door off the hinges.
- Remove the door frame. With the trim removed, you will see the frame attached to the rough opening with screws or nails. Use a screwdriver to remove any screws. If nails were used, use a pry bar to pull the frame away from the studs. You may need to cut the nails with a reciprocating saw if they are stubborn. Work from the top down, and be careful not to damage the surrounding wall.
- Inspect the rough opening. Once the old frame is out, check the condition of the studs and sill. Look for rot, water damage, or insect damage. If there is damage, repair it before installing the new door. Also, clean out any debris and old caulk.
- Dry-fit the new door. Place the new prehung door into the rough opening from the outside. It should fit snugly. Check that it is level and plumb (vertically straight). Use shims to adjust the bottom and sides. If the opening is slightly too small, you may need to trim the frame or adjust the opening.
- Secure the door frame. Starting with the hinge side, insert shims between the frame and the studs at the hinge locations. Drive long screws through the frame and shims into the studs. Do not overtighten; the frame should be snug but not bowed. Check that the door swings freely and closes properly before fully securing.
- Check the gaps and operation. Close the door and check the gaps around the top and sides. They should be even (about a quarter-inch). Open and close the door several times to ensure it operates smoothly. Adjust shims as needed.
- Insulate and seal. Use low-pressure expanding foam to fill the gaps between the frame and the rough opening. Spray a small amount, as it expands. Wait for it to dry, then trim any excess with a utility knife. Apply exterior caulk around the outside of the frame to seal against water.
- Reinstall trim. Nail the interior and exterior casing back into place. If you are using new trim, cut it to size and install it. Fill nail holes with wood filler and paint or stain as desired.
- Install hardware. Attach the lockset, deadbolt, and any other hardware according to the manufacturer’s instructions. Ensure the latch aligns with the strike plate and the door locks smoothly.
- Final adjustments. Check the weatherstripping to ensure it seals all around the door. Adjust the strike plate if necessary. Test the door from both sides to make sure it closes and locks properly.
Common Mistakes
- Not checking for square. If the rough opening is not square, the door will bind or have uneven gaps. Always check with a level and adjust with shims.
- Overtightening screws. This can bow the frame and cause the door to stick. Drive screws until snug, then check alignment.
- Using too much foam. Expanding foam can push the frame out of alignment if over-applied. Use a minimal amount and let it expand.
- Ignoring water damage. Installing a new door over rotted wood is a waste of time. Repair any structural issues first.
- Skipping the dry-fit. Always test the door in the opening before securing. It is much easier to adjust before screws are in.
Tips
- Have a helper. Doors are heavy and awkward; a second person makes the job safer and easier.
- Use shims at all hinge and latch locations for maximum stability.
- If the door is exposed to rain, install a drip cap or flashing above the door to prevent water intrusion.
- Choose a door with a high R-value for better insulation.
- Use stainless steel screws for exterior applications to prevent rust.
Troubleshooting
- Door sticks or scrapes. Check if the frame is plumb and level. Loosen the screws, adjust shims, and retighten. If the door itself is warped, you may need to plane the edge (but this is rare with prehung doors).
- Gaps are uneven. This usually means the frame is not square. Use shims to adjust the corners, and check with a level.
- Water leaks around the door. Ensure the exterior caulk is intact and the flashing is installed correctly. Check the sill pan for proper drainage.
- Door won’t latch. The strike plate may be misaligned. Loosen the screws, move it slightly, and retighten. Sometimes you need to file the hole larger.
- Frame is too tight. If the door is difficult to close, the frame may be pinched. Remove the screws, re-shim with less pressure, and re-secure.
Frequently Asked Questions
Q: Can I replace just the door slab instead of the whole frame?
A: Yes, if the frame is in good condition and the new slab matches the existing hinge and latch positions. However, it is often easier to install a prehung unit to ensure a proper fit.
Q: How do I know which swing (left or right) I need?
A: Stand outside facing the door. If the hinges are on the left, it is a left-hand door; if on the right, it is a right-hand door. Also check which side the door swings open.
Q: What if my rough opening is not a standard size?
A: You can order a custom door, or you can modify the rough opening by adding or removing framing. This is more complex and may require a contractor.
Q: How long does this project take?
A: For a beginner, expect a full day. With experience, it can be done in a few hours.
Q: Do I need a permit?
A: Usually, replacing a door does not require a permit, but it depends on your local building codes. Check with your local building department.
Q: Can I install a steel door the same way?
A: Yes, the process is the same. Just note that steel doors are heavier and may require extra shims for support.