Lighting a pilot light with an ignitor switch is a straightforward task that restores hot water, heating, or gas flow to an appliance. This guide covers the safe, step-by-step process for most modern gas appliances with a built-in spark ignitor.
What You’ll Need
- Your appliance’s manual (for exact location of the gas control valve and ignitor)
- A flashlight or headlamp
- A long lighter or match (as a backup, in case the ignitor fails)
- Gloves (optional, for grip and protection)
- Patience – some units need a few tries
Step-by-Step
- Turn off the gas. Locate the gas control valve (usually a knob with OFF/PILOT/ON positions) and turn it to OFF. Wait at least five minutes for any lingering gas to dissipate. This is critical for safety – you should not smell gas before proceeding.
- Find the pilot assembly. Look for a small copper tube leading to a burner area. The pilot light is a small flame that sits at the end of this tube. The ignitor switch is typically a red or black button near the gas valve.
- Set the valve to PILOT. Turn the gas control knob to the PILOT position. Some models require you to push the knob in while turning; others have a separate button.
- Press and hold the gas control knob down. This releases gas to the pilot. Keep it pressed throughout the next step.
- Press the ignitor switch repeatedly. While holding the gas knob down, press the ignitor button several times. You should hear a clicking sound and see a spark near the pilot. If you see a small blue flame, the pilot is lit.
- Continue holding the gas knob for about a minute. This allows the thermocouple (a safety device) to heat up and stay open. If you release too soon, the pilot will go out.
- Release the knob and check. The pilot flame should remain lit. If it stays on, turn the gas control knob from PILOT to ON.
- Set your thermostat or temperature dial. Adjust the appliance to your desired setting and confirm the main burner ignites.
Common Mistakes
- Not waiting long enough after turning off the gas. If you smell gas, you have not waited long enough. Always wait at least five minutes.
- Releasing the gas knob too early. The thermocouple needs time to heat. Releasing after a few seconds will often extinguish the pilot.
- Holding the ignitor button instead of pressing it repeatedly. Most ignitors work by generating a spark each time you press, not by holding.
- Turning the valve to ON before the pilot is stable. This can cause the pilot to go out or, worse, allow gas to escape without ignition.
- Ignoring the flame color. A yellow or orange flame indicates incomplete combustion, which can be a safety hazard.
Tips
- Read your appliance’s manual first – the exact knob positions and ignitor location vary by brand and model.
- Use a flashlight to clearly see the pilot assembly; it is often in a dark corner.
- If the ignitor does not spark, try cleaning the electrode tip with fine sandpaper or a file – a buildup of carbon can block the spark.
- Keep the area around the pilot clean and free of dust and debris.
- If you have a backup lighter, you can use it to light the pilot manually while holding the gas knob – but only after confirming the ignitor is not working.
Troubleshooting
- No spark at all: Check that the ignitor wire is connected to the electrode. If the wire is broken or loose, you may need to replace it. Also, check that the battery (if your unit uses one) is fresh.
- Pilot lights but goes out when you release the knob: This usually means the thermocouple is faulty or not positioned in the flame. Make sure the pilot flame is touching the thermocouple tip. If it is not, adjust the pilot assembly or replace the thermocouple.
- You smell gas but no flame appears: Turn the valve to OFF immediately, wait, and try again. If the problem persists, there may be a blockage in the pilot tube or a faulty gas valve – call a professional.
- Pilot flame is weak or yellow: Clean the pilot orifice with a thin wire or needle. A yellow flame suggests a dirty burner or poor air mixture; do not operate the appliance until it burns blue.
- Ignitor clicks but no spark reaches the pilot: The electrode may be misaligned. Gently bend it so that the gap between the electrode and the pilot hood is about an eighth of an inch, and the spark jumps the gap.
Frequently Asked Questions
Q: How do I know if my appliance has an ignitor switch or needs a match?
A: Look for a button labeled “IGN” or a red button near the gas valve. If you see a small wire leading to the pilot area, it likely has an ignitor. If not, you’ll need a long lighter.
Q: Why does my pilot light keep going out?
A: The most common cause is a faulty thermocouple. Over time, it can wear out or become coated with carbon. Cleaning it or replacing it usually solves the problem.
Q: Is it safe to relight a pilot light myself?
A: Yes, if you follow safety precautions: turn off the gas, wait, and ensure no gas smell before lighting. If you ever feel unsure or smell gas persistently, call a professional.
Q: What if I can’t find the pilot light?
A: Consult your appliance’s manual. The pilot is usually near the bottom of the unit, behind a small access panel. If you still can’t find it, search for the model number online or call the manufacturer.
Q: How often should the pilot light be lit?
A: For most appliances, the pilot should stay lit continuously. If you turn it off for the summer (e.g., on a water heater), you’ll need to relight it when you turn it back on.
Q: Can I use a regular match to light the pilot?
A: Yes, but use a long match or a long-reach lighter to keep your hand away from the flame. Hold the match near the pilot while pressing the gas knob.