Ribbed plastic anchors (sometimes called ribbed plugs or universal anchors) are a fast, reliable way to hang shelves, curtain rods, and other items on hollow drywall or solid masonry. The ribs grip the surrounding material and keep the anchor from spinning as you drive the screw, so the finished hold is firm and the screw stays put. Before you start, make sure you have the right anchor size for your screw and the weight you plan to hang, and confirm the wall is not hiding electrical wires or plumbing.
What You’ll Need
- Ribbed plastic anchors (sized to match your screw)
- Screws that fit the anchor’s inner diameter
- Power drill or screwdriver
- Drill bit (slightly smaller than the anchor’s outer diameter)
- Hammer (optional, for tapping anchors into place)
- Pencil or marker
- Level (for positioning)
- Stud finder (if hanging something heavy on drywall)
Step-by-Step
- Choose the right anchor. Ribbed plastic anchors come in a few sizes. Match the anchor to the screw: the screw should pass through the anchor’s hole without forcing, and the anchor’s outer diameter should be slightly larger than the hole you’ll drill. Check the packaging for the recommended screw gauge and maximum load.
- Mark the hole locations. Hold the item you’re mounting against the wall, use a level to make sure it’s straight, and mark each screw hole with a pencil. If you’re hanging something heavy (like a large mirror or a shelf), use a stud finder to locate a wall stud and plan to screw into the stud instead of using anchors—anchors are for hollow drywall or masonry, not for supporting very heavy loads alone.
- Drill pilot holes. Choose a drill bit that is slightly smaller than the outer diameter of the anchor. For drywall, you can often skip the pilot hole if the wall is thin, but drilling a pilot hole reduces the risk of cracking the drywall and makes insertion easier. For masonry (brick, concrete, or block), you must drill a pilot hole using a masonry bit. Drill straight into the wall at each mark.
- Clean the hole. Remove any dust or debris from the hole. You can blow into it, use a vacuum, or push a small brush in and out. A clean hole lets the anchor seat fully and grip better.
- Insert the anchor. Push the ribbed anchor into the hole by hand. If it’s snug, tap it gently with a hammer until the flange (the lip) is flush with the wall surface. Do not hammer so hard that you deform the anchor or damage the drywall.
- Drive the screw. Place the screw into the anchor and drive it with a screwdriver or drill set to a low torque. The screw should pull the anchor tight against the back of the drywall (if it’s a hollow-wall anchor) or expand slightly in masonry. Stop when the screw is snug—do not overtighten, or you’ll strip the anchor or crush the drywall.
- Mount your item. Align the item with the installed screws and tighten them fully. If the item has keyhole slots, you may need to leave the screws slightly proud of the wall, then slide the item down into place.
Common Mistakes
- Drilling too large a hole. If the pilot hole is bigger than the anchor, the anchor won’t grip—it will spin or pull out. Always test the bit size against the anchor before drilling the wall.
- Using the wrong screw. A screw that’s too thick will split the anchor; one that’s too thin won’t engage the ribs and may pull out. Check the anchor’s packaging for the recommended screw gauge.
- Hammering too hard. You can crush the drywall or bend the anchor. Tap gently; the anchor should go in with moderate force.
- Overtightening the screw. This strips the anchor’s internal threads, leaving the screw loose. Stop as soon as the screw is snug.
- Using anchors for heavy loads on drywall. Ribbed plastic anchors are great for light to medium loads (like a small shelf or a curtain rod), but for anything heavy, screw into a stud or use a toggle bolt.
Tips
- If you’re installing multiple anchors, mark and drill all holes first, then insert all anchors before mounting the item—this keeps the alignment consistent.
- For masonry, use a hammer drill with a masonry bit and drill slowly to avoid overheating the bit. Wear safety glasses to protect your eyes from dust and chips.
- If the anchor is loose in the hole, remove it and wrap a small piece of tape around the ribs to add friction, or use a slightly larger anchor.
- When driving the screw, apply steady, even pressure. If the screw starts to resist, back it out and check that the anchor is aligned—don’t force it.
- Keep a few spare anchors on hand in case one gets damaged during installation.
Troubleshooting
- The anchor spins in the hole. This usually means the pilot hole is too large or the anchor is too small. Remove the anchor, fill the hole with a bit of wall repair compound or a wooden matchstick (for drywall), let it dry, and re-drill a smaller hole. Or switch to a larger anchor.
- The screw won’t go in. The anchor may be misaligned or the screw may be too thick. Check that the screw fits the anchor’s hole. If it’s a masonry wall, the anchor might not be fully seated—tap it in a bit more.
- The screw strips the anchor. This happens when you overtighten or use a screw that’s too large. Remove the screw, insert a new anchor (if the old one is damaged), and drive the screw gently with a manual screwdriver to feel the resistance.
- The anchor pulls out of the wall. The load may be too heavy for the anchor type or the drywall is too thin. Move to a stud or use a toggle bolt. For masonry, use a masonry anchor instead of a plastic one.
- The drywall cracks around the anchor. This often happens when drilling without a pilot hole or hammering too hard. Patch the crack with spackle, let it dry, sand, and re-drill a fresh hole nearby.
Frequently Asked Questions
Q: Can I use ribbed plastic anchors in tile?
Not directly. The ribs are designed for drywall and masonry, not tile. For tile, you’d need a tile-specific anchor or a masonry bit and a plastic anchor that fits the tile’s thickness—but it’s risky. Better to drill into the grout line or use a toggle bolt if possible.
Q: Do I need a pilot hole for drywall?
It’s recommended, especially for thicker drywall or if you’re near an edge. A pilot hole prevents cracking and makes insertion easier. For thin drywall, you can sometimes push the anchor in directly, but a pilot hole is safer.
Q: How much weight can a ribbed plastic anchor hold?
It depends on the anchor size and wall material. A typical anchor in drywall can hold a few pounds to maybe ten pounds, but for anything heavier, use a stud or a toggle bolt. Check the packaging for the manufacturer’s rating.
Q: Can I remove a ribbed plastic anchor later?
Yes, you can unscrew the screw and then pull the anchor out with pliers. If it’s stuck, you can push it into the wall cavity (for drywall) and patch the hole. For masonry, you may need to drill it out.
Q: What’s the difference between ribbed anchors and other plastic anchors?
Ribbed anchors have longitudinal ridges that grip the wall material and prevent rotation. Other types, like cone or expansion anchors, work differently—some expand behind the wall. Ribbed anchors are simple and reliable for light to medium loads.
Q: Can I reuse a ribbed plastic anchor?
Usually not. Once removed, the ribs may be worn or the hole may be enlarged. It’s best to use a fresh anchor in a new location or fill the old hole and re-drill.