Installing a lid support—also called a gas strut, gas spring, or pneumatic hinge—makes a heavy lid open smoothly and stay open on its own, so you don’t need a prop or a second hand. This guide covers the basic process for a typical cabinet, chest, or toolbox lid. Before you start, confirm the support you bought matches the weight and size of your lid, and check that you have the correct mounting brackets for your application.
What You’ll Need
- Lid support (gas strut) with the correct force rating for your lid
- Mounting brackets (often included, but verify they fit your cabinet)
- Screwdriver or drill with appropriate bits
- Pencil or marker
- Measuring tape or ruler
- Level (optional but helpful)
- Safety glasses
Step-by-Step
- Read the manufacturer’s instructions. Different lid supports have specific mounting requirements, so check the included manual for recommended positions and any special notes.
- Determine the correct orientation. Gas struts are usually filled with pressurized gas and oil. They often have a rod and a cylinder; the rod should typically point downward or at a slight angle to ensure proper lubrication and smooth operation. Check the instructions for the recommended orientation.
- Measure and mark the mounting points. Hold the lid support in place with the lid closed and the support compressed. Mark the locations for the brackets on both the cabinet frame and the lid. A common method is to mount the cylinder end to the cabinet and the rod end to the lid, but follow your product’s guidance.
- Install the brackets. Attach the mounting brackets to the marked spots using the provided screws. If you’re drilling into wood, pre-drill pilot holes to prevent splitting. For metal, use a center punch and appropriate drill bit. Ensure the brackets are secure and aligned.
- Attach the lid support. Connect the ball studs or pins of the support to the brackets. Some supports use a clip or a screw-on ball joint. Make sure the support snaps or locks into place securely.
- Test the lid. Slowly open the lid. It should move smoothly and stay open at the desired angle. If it closes too quickly or doesn’t stay up, you may need a support with a different force rating.
- Adjust if necessary. If the lid doesn’t open fully or the support binds, loosen the brackets slightly and reposition them. Re-tighten once the movement is smooth.
Common Mistakes
- Choosing the wrong force rating. A support that’s too weak won’t hold the lid up; one that’s too strong can be hard to close and may damage the lid or hinges.
- Incorrect orientation. Installing the strut upside down can cause it to fail prematurely or not work at all.
- Poor bracket placement. Mounting brackets too close to the hinge or too far from it can affect the leverage and the lid’s opening angle.
- Not pre-drilling holes. Screwing directly into wood can crack it, especially near edges.
- Forgetting to check for clearance. The support might hit an internal shelf or component when the lid opens.
Tips
- Measure the lid’s weight and length to select the correct gas spring. Many suppliers provide charts or calculators.
- Use a piece of tape to hold the support in place while you test the lid before final tightening.
- If your lid is heavy, consider using two supports, one on each side, for balanced operation.
- Keep the rod clean and avoid scratching it; damage can cause leaks.
- For a clean look, choose brackets that match your cabinet finish.
Troubleshooting
The lid won’t stay up. The support is likely too weak. Check the force rating and replace with a stronger one. Also verify that the support is fully extended and not blocked.
The lid slams shut. The support may be too strong, or the mounting position may give too much leverage. Try a weaker support or adjust the bracket positions.
The support makes noise. A slight hiss is normal, but a loud squeak or grinding could mean the rod is rubbing against something or the ball joint is dry. Lubricate the joint with a silicone spray and check alignment.
The support doesn’t compress. If the lid won’t close, the support might be installed upside down or the force is too high. Check orientation and consider a lower force.
Brackets are loose. If screws pull out, the material may be too thin. Use larger screws or add a backing plate.
Frequently Asked Questions
How do I know what force rating I need?
You need to know the weight of the lid and the distance from the hinge to the mounting point. Most manufacturers provide a formula or chart. As a rule of thumb, a heavier lid or a longer lid requires a higher force rating.
Can I install a lid support on any type of lid?
Most hinged lids that open upward can work, including cabinets, chests, toy boxes, and toolboxes. However, you must ensure the mounting surface is sturdy enough and that the support doesn’t interfere with the lid’s operation.
Do I need two supports for a large lid?
For wide or heavy lids, two supports are often recommended to distribute the load evenly and prevent twisting. Check the manufacturer’s guidelines for maximum lid size per support.
Can I shorten a gas strut?
No, you should not cut or modify a gas strut. It is a sealed unit under pressure. Cutting it can cause it to fail dangerously. Instead, choose a support with the correct length.
How long do lid supports last?
With normal use, a quality gas spring can last for many years. Over time, the gas can slowly leak, and the support will lose force. When that happens, replace it.
Can I install a lid support on a lid that opens sideways?
Lid supports are designed for lids that open upward. For sideways-opening doors, you’d typically use a different mechanism, like a soft-close hinge or a door stay.