How to Install a Toilet Below Grade

Installing a toilet below grade means placing it in a basement or lower level of your home, where the drain line sits below the main sewer or septic outlet. This requires a special setup because gravity alone won’t carry waste upward. The standard solution is a macerating toilet or a sewage ejector pump system that grinds and pumps waste to a higher drain line. This guide covers the full process, from planning to final installation.

What You’ll Need

  • Macerating toilet unit (or a standard toilet plus a sewage ejector pump system)
  • PVC pipe and fittings for the vent and discharge lines
  • Pipe wrenches, adjustable wrench, and pliers
  • Screwdriver set and drill with bits
  • Level
  • Measuring tape
  • Wax ring or rubber gasket (depending on your unit)
  • Teflon tape and pipe joint compound
  • Bucket, rags, and safety gloves
  • Vent pipe and vent cap (if not included)
  • Check local plumbing codes for specific requirements

Step-by-Step

  1. Check local codes and plan the layout. Before buying anything, verify that a macerating toilet or ejector pump is allowed in your area. Determine where the discharge line will connect to the existing plumbing—usually a vertical stack or a horizontal line that leads to the main sewer. Measure the distance and elevation rise from the toilet location to that connection point.
  2. Choose the right system. For most below-grade installations, a macerating toilet is the simplest option because it includes a built-in pump and macerator. If you already have a standard toilet, you can install a separate sewage ejector pump basin nearby, but that requires more space and additional plumbing. Ensure the pump’s discharge head (the height it can pump) meets your needs.
  3. Prepare the installation site. Clear the area and ensure the floor is level. If you’re installing a macerating toilet, you’ll need to place the unit against a wall that provides access to the discharge pipe and an electrical outlet. For a standard toilet with a separate pump, you’ll need to dig or cut a hole for the pump basin, which can be a major project in a concrete floor.
  4. Install the macerating toilet base. Most macerating toilets come as a single unit with the bowl and pump housing. Position the unit so the discharge outlet aligns with where you’ll run the pipe to the main drain. The unit typically has a built-in vent, but some models require an external vent—check the manufacturer’s instructions. Secure the base to the floor using the provided brackets or screws.
  5. Connect the discharge pipe. Use the supplied pipe and fittings to run the discharge line from the pump to the main drain. The pipe must have a continuous upward slope (usually at least 1/4 inch per foot) to help waste flow. Connect to the main drain using a wye fitting or a sanitary tee. Make sure all connections are tight and use Teflon tape on threaded joints.
  6. Install the vent. If your system requires a separate vent, connect a pipe from the vent outlet on the pump to a vent stack or run it to the exterior. The vent prevents air locks and allows the pump to operate efficiently. Follow local codes for vent sizing and termination.
  7. Mount the toilet bowl. For a macerating toilet, the bowl attaches to the base with bolts. Place the wax ring or rubber gasket on the discharge outlet, then set the bowl in place. Tighten the bolts evenly to create a seal. For a standard toilet, set the bowl over the flange connected to the pump basin.
  8. Connect the water supply. Attach the water supply line from the wall shut-off valve to the toilet tank. Use Teflon tape on the threads and tighten with a wrench. Turn on the water and check for leaks.
  9. Plug in the pump. Macerating toilets require electricity to operate the pump. Plug the unit into a dedicated GFCI-protected outlet. Make sure the cord is not pinched or near any sharp edges.
  10. Test the system. Flush the toilet several times with water only, then with a small amount of toilet paper. Listen for the pump to activate and run until the discharge is clear. Check all connections for leaks. If everything works, you’re done.

Common Mistakes

  • Incorrect venting: Skipping or improperly installing the vent can cause slow flushing, gurgling, and sewer gas odors.
  • Too much slope on the discharge pipe: While a slope is needed, too steep a slope can cause the waste to separate from the water, leading to clogs. Stick to the manufacturer’s recommended slope.
  • Using the wrong pipe size: Discharge pipes are typically 3/4 inch or 1 inch, but using a larger pipe can reduce the velocity and cause solids to settle. Always follow the system’s specifications.
  • Forgetting to plug in the pump: It sounds obvious, but many people forget to connect power, leading to a non-flushing toilet.
  • Not checking local codes: Some areas require a licensed plumber for this type of work, and failing to get a permit can cause issues later.

Tips

  • Place the macerating toilet near a wall with easy access to electrical power and the main drain to minimize pipe runs.
  • Use a GFCI outlet for safety, as the area may be damp.
  • Before finalizing the location, dry-fit all pipes to ensure you have the right lengths and angles.
  • Consider adding a cleanout fitting in the discharge line for future maintenance.
  • Read the manufacturer’s manual thoroughly—different models have specific requirements for venting and pipe routing.

Troubleshooting

  • Toilet won’t flush or pump doesn’t run: Check that the unit is plugged in and the GFCI hasn’t tripped. Inspect the pump’s float switch to ensure it’s not stuck. If the pump hums but doesn’t work, it may be jammed—turn off power and clear any debris.
  • Water backs up into the bowl: This usually indicates a clog in the discharge line. Turn off the power, remove the access panel on the pump, and clear the obstruction. Also check that the vent isn’t blocked.
  • Gurgling sounds from other drains: This suggests a venting problem. Ensure the vent is open and correctly sized. If the issue persists, consult a plumber.
  • Odors coming from the toilet: Check the wax ring seal and ensure the vent is functioning. If odors continue, the pump’s filter may need cleaning.
  • Pump runs continuously: The float switch might be stuck in the ‘on’ position. Turn off power, clean the switch, and test again.

Frequently Asked Questions

  • Can I install a standard toilet in a basement without a pump? No, if the drain is below the main sewer line, you need a pump to lift waste. A standard gravity toilet won’t work.
  • How much space does a macerating toilet need? Most units are compact and fit in a small bathroom, but you need access to the rear for connections. Check the dimensions before buying.
  • Can I connect a sink or shower to the macerating unit? Some models have additional inlet ports for a sink or shower, but not all. Check the specifications and local codes.
  • Is it noisy? Macerating toilets make a grinding sound during flushing, which lasts a few seconds. It’s normal and not excessively loud.
  • Do I need a permit? Most plumbing installations require a permit, especially for below-grade work. Check with your local building department.
  • Can I do this myself? If you’re comfortable with basic plumbing and electrical work, yes. But if you’re unsure, hiring a licensed plumber is safer and ensures code compliance.