How to Fix an Uneven Paver

An uneven paver is not just an eyesore; it’s a tripping hazard and a sign that the base beneath has shifted or eroded. Fixing it involves lifting the paver, correcting the base, and re-setting it so it sits level with its neighbors. With a few basic tools and some patience, you can restore a safe, even surface in a couple of hours.

What You’ll Need

  • Flat-head screwdriver or pry bar
  • Rubber mallet
  • Shovel or trowel
  • Coarse sand or stone dust (for bedding)
  • Crushed stone or gravel (for base repair, if needed)
  • Level (spirit level)
  • Broom
  • Plate compactor (optional, for large areas)
  • Safety glasses and work gloves

Step-by-Step

  1. Identify the uneven pavers. Walk over the area and note which pavers are raised, sunken, or rocking. Mark them with chalk or a piece of tape.
  2. Remove the paver. Insert a flat-head screwdriver or pry bar into the joint between the uneven paver and its neighbors. Gently pry upward. If the paver is tightly set, tap the screwdriver with a rubber mallet to create a gap. Lift the paver straight out to avoid chipping the edges.
  3. Inspect the base. Look at the hole left behind. The base should be a layer of compacted crushed stone or gravel, topped with a thin layer of sand. If you see bare soil, roots, or a lot of missing sand, the base has failed.
  4. Remove and replace damaged base material. Use a trowel or shovel to remove any soft, wet, or contaminated base material. Dig down a few inches until you reach firm, stable ground. Fill the hole with crushed stone or gravel, compacting it in layers (a few inches at a time) using a hand tamper or the end of a 2×4. The top of the base should be about an inch below the surface of the surrounding pavers.
  5. Add a fresh sand bed. Spread a layer of coarse sand or stone dust over the compacted base. Use a straight board to screed the sand level, making it about an inch thick. The sand should be slightly higher than the final desired height, because it will settle when you tap the paver.
  6. Set the paver. Place the paver back into the opening. Gently tap it with a rubber mallet until it is level with the adjacent pavers. Use a spirit level to check that it is flat in both directions.
  7. Fill the joints. Sweep fine sand or polymeric sand into the gaps between the pavers. If you use polymeric sand, wet it lightly with a hose to activate the binding agents (follow the manufacturer’s instructions). For regular sand, just sweep it in and let it settle.
  8. Compact and settle. If you have a plate compactor, run it over the repaired area to settle the sand and paver. If not, use a rubber mallet to tap the paver gently all around its edges. Then sweep more sand into the joints if needed.
  9. Check your work. Walk over the repaired area and ensure the paver is stable and level. Re-tap or add sand if necessary.

Common Mistakes

  • Skipping the base repair. If you just add sand under a sunken paver, it will sink again within a few weeks. Always address the underlying base.
  • Using the wrong sand. Fine play sand can wash away easily. Use coarse sand or stone dust specifically for paver bedding.
  • Not compacting the base. Loose base material will settle, causing the paver to sink again. Compact every layer thoroughly.
  • Over-tapping. Hitting the paver too hard can crack it or chip the edges. Use gentle taps and check frequently.
  • Ignoring drainage. If water pools under the paver, it will erode the base. Ensure the area slopes slightly away from structures.

Tips

  • Work on a dry day. Wet sand is harder to handle and compacts unevenly.
  • If you’re fixing several adjacent pavers, remove them all at once and re-level the entire area for a consistent surface.
  • Use a string line or a straight board to check that the repaired paver aligns with the surrounding ones.
  • For a quick fix on a slightly raised paver, you can sometimes just tap it down with a rubber mallet, but this only works if the base is still intact.
  • Keep a bag of sand and a few spare pavers on hand for future repairs.

Troubleshooting

The paver still rocks after re-setting. This usually means the base is still uneven. Remove the paver again, check for high spots, and add or remove sand as needed.

The paver sinks again after a few weeks. The base is likely still too soft or the sand bed is too thick. Remove the paver, dig deeper, and compact more crushed stone. You may need to replace the sand with a thinner layer.

The paver is cracked. If the paver itself is cracked, you’ll need a replacement. Remove the cracked paver and use a new one that matches the size and color. If you don’t have a spare, check with a local home improvement store or a paver manufacturer.

Polymeric sand is not hardening. This can happen if the sand is too wet or too dry when applied. Follow the manufacturer’s instructions carefully. If it doesn’t harden, you may need to remove it and start over.

The surrounding pavers are also shifting. This indicates a larger problem with the base. You may need to remove a larger section and re-compact the entire base. Consider hiring a professional if the area is extensive.

Frequently Asked Questions

Q: Can I fix an uneven paver without removing it?
A: Sometimes, if the paver is only slightly raised, you can tap it down with a rubber mallet. For sunken pavers, you generally need to lift them to add material underneath.

Q: How often do pavers need maintenance?
A: It depends on the climate and usage. In most cases, a quick inspection each spring and fall is enough. Re-sanding joints every few years can help prevent shifting.

Q: What is the best base for pavers?
A: A compacted layer of crushed stone or gravel, topped with a thin layer of coarse sand, is the standard. The crushed stone provides drainage and stability, while the sand allows for precise leveling.

Q: Can I use polymeric sand for the bedding layer?
A: No. Polymeric sand is for joints only. For bedding, use plain coarse sand or stone dust.

Q: Why does my paver keep sinking in the same spot?
A: This usually means there is a soft spot in the soil or a drainage issue. You may need to excavate deeper and add more crushed stone, or improve drainage in the area.

Q: Should I seal my pavers after fixing them?
A: Sealing is optional but can help protect the pavers from stains and weed growth. It doesn’t prevent shifting, but it can extend the life of the surface.