Fixing a leaky tub faucet stops the drip, saves water, and prevents long-term damage to your tub’s finish and the plumbing behind the wall. Most leaks come from a worn-out rubber washer or O-ring inside the handle assembly, and you can replace it in under an hour with basic tools.
What You’ll Need
- Adjustable wrench or pliers
- Screwdriver (flathead and Phillips)
- Replacement washers or O-rings (match the size and shape of the old ones)
- Plumber’s grease (silicone-based)
- Penetrating oil (if the handle is stuck)
- Clean rag or towel
- Bucket or shallow pan (to catch drips)
- Optional: faucet repair kit that matches your faucet brand
Step-by-Step
- Turn off the water supply. Look for the shut-off valves under the sink or near the tub. Turn them clockwise until they stop. If there are no local valves, shut off the main water valve for the house. Open the faucet to release any remaining water pressure.
- Plug the drain. Place a rag or stopper in the tub drain to catch small parts like screws or washers that might fall.
- Remove the handle. Pry off the decorative cap on top of the handle (often marked with a red or blue indicator). Underneath, you’ll find a screw. Remove it and gently pull the handle straight off. If it’s stuck, apply penetrating oil around the base and wait a few minutes before wiggling it free.
- Take off the trim and escutcheon. The chrome ring that covers the hole in the wall may unscrew by hand or require a wrench. Some models have small set screws. Remove it to expose the valve body.
- Remove the stem or cartridge. You’ll see a brass stem (for compression faucets) or a cartridge (for cartridge-style). Use a wrench on the hex nut where the stem meets the valve body. Turn it counterclockwise. If it resists, apply penetrating oil and wait.
- Inspect the old parts. Look at the rubber washer on the bottom of the stem (for compression) or the O-rings on the cartridge. Note their size and shape. If they’re flat, cracked, or mushy, that’s your leak.
- Replace the washer or O-rings. Remove the old ones (a small screw holds the washer on some stems). Install the new ones, pressing them into place. Apply a thin coat of plumber’s grease to the O-rings or the threads of the stem to help them slide and seal.
- Reassemble in reverse order. Screw the stem or cartridge back in by hand first, then snug it with a wrench. Don’t overtighten—finger-tight plus a quarter turn is usually enough. Replace the escutcheon, handle, and decorative cap.
- Turn the water back on. Slowly open the shut-off valves or main valve. Turn the faucet on and off a few times to test for drips. Check under the handle and around the escutcheon for any moisture.
Common Mistakes
- Forgetting to turn off the water. This leads to a flood and potential injury. Always shut off the supply first.
- Overtightening the packing nut. That nut holds the stem in place; too much force can crack the valve body or strip threads.
- Using the wrong replacement part. Bring the old washer or cartridge to the hardware store to match it exactly. A slightly different size won’t seal.
- Skipping the grease. Dry O-rings can bind or tear during reassembly, causing a new leak.
- Leaving the handle loose. If the handle isn’t seated properly, it can wobble and eventually strip the splines.
Tips
- Take a photo of the disassembled parts before you remove anything—it helps during reassembly.
- If the stem is hard to turn, use a wrench with a cloth to protect the finish.
- Replace both the washer and the seat (the metal ring inside the valve) if the seat is rough or pitted. Some repair kits include a seat wrench.
- For cartridge faucets, note the orientation (which side faces up) before pulling it out—many cartridges are directional.
- Clean any mineral deposits off the valve body with vinegar before reassembling.
Troubleshooting
- Water still drips after replacing the washer. The valve seat inside the faucet may be worn. Use a seat dressing tool to smooth it, or replace the seat if it’s removable.
- Leak comes from under the handle, not the spout. That’s usually a worn O-ring on the stem or cartridge. Replace all O-rings, not just the one that looks bad.
- Handle won’t come off. Apply penetrating oil, wait, and tap gently with a rubber mallet. If it still won’t budge, the handle may be corroded to the stem—use a puller tool designed for faucet handles.
- You can’t find the shut-off valves. If there are none under the sink, you’ll need to shut off the main water valve for the house. This is usually near the water meter or where the main line enters.
- The stem or cartridge is stuck in the valve body. Do not force it—you can crack the valve. Apply penetrating oil, wait, and try again. If it still won’t move, call a plumber.
- After reassembly, the faucet is loose or wobbly. The packing nut or retaining nut may be loose. Tighten it gently, but don’t overtighten.
Frequently Asked Questions
Q: How do I know if my faucet is a compression or cartridge type?
A: Compression faucets have separate hot and cold handles and use rubber washers. Cartridge faucets often have a single handle (though some have two) and use a plastic or brass cartridge. Look for a brand name on the handle or escutcheon to find the right parts.
Q: Can I fix a leak without turning off the water?
A: No. You must shut off the water supply. Attempting to remove a stem or cartridge under pressure will cause a spray of water and can damage the valve.
Q: Why does my faucet drip only when the handle is in a certain position?
A: That usually means the washer or O-ring is worn unevenly, or the valve seat has a rough spot. Replacing the washer and dressing the seat should fix it.
Q: Is it worth repairing an old faucet instead of replacing it?
A: If the faucet is otherwise in good condition, a simple washer replacement costs just a few dollars. But if the valve body is corroded or cracked, replacement may be more practical.
Q: What if my faucet has a single handle and no visible screws?
A: Look for a small set screw on the side or under the handle, or a decorative cap that pries off. Some modern handles have a hidden screw behind a small plastic insert.
Q: Can I use regular grease instead of plumber’s grease?
A: No. Regular grease can break down rubber and cause leaks. Use a silicone-based plumber’s grease, which is safe for washers and O-rings.