To cover brick corbels on a fireplace with wood, you build a wooden box or frame around each corbel and attach it securely, either by screwing into the brick with masonry anchors or by using construction adhesive. This creates a clean, finished look that matches your mantel or surrounding trim, hiding the brick entirely.
What Brick Corbels Are and Why Cover Them
A brick corbel is a structural or decorative projection built out from the main chimney or fireplace face, often in stepped layers. They commonly support a mantel shelf, a hearth, or simply add visual weight to the fireplace design. Many homeowners find them dated or too rustic, especially after renovating the rest of the room.
Covering them with wood is a popular remodeling approach because it transforms the fireplace’s appearance without touching the masonry or dealing with demolition dust. It also allows you to match the wood species and stain of your existing mantel, baseboards, or built-in shelving for a cohesive look.
How the Wood Covering Process Works
The basic method is to create a three-dimensional skin that fits snugly over the corbel’s shape. You measure the corbel’s height, depth, and width, then cut wood panels for the front face, the side face (if the corbel is exposed on the side), and the top and bottom caps. The panels are assembled like a simple box, then slid over the brick and fastened.
For corbels that are flush against a wall on one side, you only need the front, top, and bottom pieces, plus a side piece if the outer edge is visible. The back of the box remains open, resting against the brick. This open-back design makes installation far easier, as you do not need to notch wood around the brick’s irregular surface.
You can build the box in place, piece by piece, or pre-assemble it and then slide it over the corbel. Pre-assembly works best when the corbel has a simple rectangular profile. For stepped or tapered corbels, building in place with a trim router or coping saw is more practical.
Choosing the Right Wood and Tools
Solid wood is the usual choice, with common options being oak, poplar, maple, or pine. Poplar is a favorite for painting because it is stable and takes primer well. Oak or maple are better if you plan to stain, as they have attractive grain. Avoid particleboard or MDF near a fireplace, as heat can cause the adhesives in these panels to break down over time.
You will need a few basic tools: a tape measure, a circular saw or miter saw for cutting, a drill with masonry bits, a hammer, a level, and a caulk gun. For fastening, use masonry screws (often called Tapcon-style) or a high-temperature construction adhesive rated for masonry. If the corbel is purely decorative and not load-bearing, adhesive alone may suffice, but screws are more secure.
Step-by-Step Installation Guide
Follow these steps for a typical rectangular corbel:
- Measure carefully: Record the corbel’s height, depth, and width at its widest points. Add about a quarter-inch to the depth and width so the wood box fits over the brick without forcing.
- Cut the panels: Cut the front panel to the full height and width. Cut the side panel (if needed) to the same height and the measured depth. Cut the top and bottom caps slightly larger than the box footprint so they create a small lip.
- Assemble the box: Attach the front to the side using wood glue and finishing nails. Attach the top and bottom caps. Leave the back open.
- Dry-fit the box: Slide the box over the corbel. It should sit snugly but not require hammering. Trim the inside edges with a chisel or sandpaper if it binds.
- Secure to the brick: Drill pilot holes through the wood and into the brick at several points (top, bottom, and middle). Use a masonry bit slightly smaller than the screw’s core. Drive masonry screws until snug, but do not overtighten, as this can crack the brick.
- Fill and finish: Fill nail holes and seams with wood filler, sand smooth, then prime and paint or stain and seal. Apply caulk along the top edge where the wood meets the brick to hide any gap.
Common Problems and How to Avoid Them
One frequent issue is the wood box not fitting flush against the brick because the corbel is not perfectly square. Use shims made of thin wood strips behind the panels to level the face before securing. Another problem is heat damage: if the corbel is very close to the firebox, the wood can dry out or discolor. Maintain a clearance of at least a few inches between the wood and the firebox opening, and check your local building codes for minimum clearances.
Masonry screws can strip if you drill the pilot hole too large. Test on a scrap brick first, or use a hammer drill for cleaner holes. If the corbel is load-bearing (supporting a heavy stone or tile mantel), do not remove the brick; the wood is only a cosmetic cover, and the brick must stay in place.
Costs and Time Considerations
The cost depends mostly on the wood species and the size of the corbels. A single corbel might require a few board feet of lumber, which is inexpensive for pine but more for oak. You will also need screws, adhesive, wood filler, and finish materials. Overall, this is a low-cost project compared to rebuilding the fireplace, and most of the expense is your labor.
Time-wise, a simple box cover for one corbel can be cut and installed in a couple of hours, not including drying time for glue, filler, and paint. Stepped corbels with multiple layers take longer because each step needs its own piece of trim. Plan for a weekend if you have two corbels and want a polished painted finish.
Alternatives to Full Wood Covers
If you like the brick but want a softer look, consider painting the corbels with heat-resistant masonry paint instead of covering them. Another option is to wrap only the front face with a thin wood veneer panel, leaving the sides exposed. For a more modern approach, you could install a prefabricated mantel surround that sits in front of the corbels, hiding them without individual boxes. Each method has trade-offs: painting is fastest, veneer is thinner but harder to fasten, and a full surround changes the whole fireplace profile.
Safety and Building Code Notes
Before starting, check your local building codes regarding clearances from combustible materials to the firebox. Many codes require a minimum distance between wood trim and the firebox opening, often measured in inches. If your corbels are within that zone, you may need to use a non-combustible material like metal or stone instead. Also, ensure that your wood covering does not block any air vents or dampers on the fireplace. If you have a gas fireplace, consult the manufacturer’s manual, as clearance requirements can be stricter than for wood-burning units.
Frequently Asked Questions
Can I use plywood instead of solid wood? Yes, but use a high-quality plywood with a hardwood face, and avoid it near the firebox if heat is a concern. Plywood is more stable than solid wood for wide panels, but the edges will need veneer tape or trim to look finished.
Do I need to remove the brick corbel first? No, you should not remove it. The corbel is often structural, and removing it could weaken the chimney or fireplace. The wood cover goes over it, so the brick stays intact.
What if my corbel is an odd shape, like stepped or angled? Build the cover in sections, one step at a time. Use a cardboard template to trace each step’s profile, then transfer that to wood. For angled corbels, cut the wood with a miter saw to match the angle, and use wood filler to smooth the joints.
How do I attach wood without drilling into the brick? You can use a high-temperature construction adhesive alone, but this is less secure. If the corbel is purely decorative, adhesive may hold for years. For a load-bearing or high-traffic area, screws are safer. You can also use a combination: adhesive plus a few screws for peace of mind.
Will the wood get too hot to touch? If the corbel is near the firebox, the wood can become warm but should not be hot if clearances are met. If you notice the wood getting hot during a fire, you have a clearance problem and should stop using the fireplace until you address it. Consider adding a metal heat shield or using a non-combustible material instead.