A mow strip—also called a mowing edge or border—is a narrow, hard surface laid flush with the lawn that lets you run one mower wheel along it, so you never have to trim grass against a bed, fence, or wall by hand. The easiest way to build one is to set flexible plastic edging in a shallow trench and backfill it with gravel or concrete, but the truly simplest method for most homeowners is to install preformed metal or plastic edging that you simply hammer into the ground. This article covers the options, the steps, and the common mistakes so you can pick the method that fits your yard and skill level.
What a Mow Strip Actually Does
A mow strip creates a clean, permanent boundary between turf and a garden bed, path, or structure. Instead of using a string trimmer along every edge after each mowing, you guide the mower’s wheel along the strip. The strip supports the wheel, keeping the mower deck level, so the blade cuts the grass right at the edge without scalping the lawn or leaving a ragged line. It also stops grass from creeping into beds and keeps mulch or gravel from spilling onto the lawn.
The strip can be flush with the soil or slightly above it. A flush strip is easiest to mow over because the wheel rolls smoothly from grass to strip. A slightly raised strip (about a half inch) is easier to see and less likely to be covered by soil or mulch, but it can catch mower blades if the mower is set too low.
Why the Easiest Method Depends on Your Yard
There is no single easiest method for every situation. The best choice depends on three things: the shape of the edge, the type of mower you use, and how much disturbance you are willing to tolerate in existing beds.
- Straight or gently curved edges: Preformed metal or plastic edging works well because it can follow broad curves.
- Tight curves or intricate shapes: Flexible plastic edging (often sold in rolls) is easier to bend sharply.
- Existing plants close to the edge: Hammer-in edging is less disruptive because it does not require digging a wide trench.
- Heavy mowers (riding mowers): A wider, sturdier strip made of concrete pavers or poured concrete is better because it can bear the weight without sinking.
- Walk-behind mowers: Most edging types work fine, as the wheel load is light.
If you have a riding mower, a thin metal strip may bend under the weight. In that case, the easiest durable option is a row of concrete pavers laid on a compacted sand base, which is still a simple weekend project.
The Hammer-In Edging Method (Least Tools, Fastest)
This is the quickest way to get a functional mow strip, especially for straight or gently curved beds. You buy metal or rigid plastic edging stakes that have a flat top and a pointed bottom. You simply place the edging along the desired line and tap it into the ground with a rubber mallet.
- Mark the line: Use a garden hose or rope to lay out the edge shape.
- Position the edging: Place the first section along the line, with the top of the edging at or slightly above the soil level.
- Tap it in: Use a rubber mallet to drive the edging down until the top is flush with the lawn. Avoid a metal hammer, which will dent the edging.
- Overlap sections: Follow the manufacturer’s instructions for connecting pieces; most have a lip or notch that locks sections together.
- Backfill if needed: If there are gaps between the edging and the soil, push soil back against it to stabilize it.
This method works best in soft, loamy soil. In heavy clay or rocky ground, you may need to first cut a narrow slit with a flat spade or an edging tool, then hammer the edging into that slit. The whole process for a typical bed edge takes a couple of hours, and you can mow immediately afterward.
The Trench-and-Gravel Method (More Durable, Still Simple)
If you want a strip that will last for years and can handle a riding mower, the trench method is a better choice. It involves digging a shallow trench, filling it with a base, and setting a hard surface on top.
- Dig a trench: Use a flat spade to cut a trench about three inches deep and four inches wide along the marked line.
- Add a base: Fill the bottom of the trench with a couple of inches of compacted gravel or sand. This prevents settling.
- Set the surface: Lay concrete pavers, bricks, or a precast concrete edging block in the trench, flush with the lawn. Tap each one level with a rubber mallet.
- Fill gaps: Sweep sand or fine gravel into the joints between pavers to lock them in place.
- Compact: Tamp the surface gently with a hand tamper or the back of a shovel to settle everything.
This method takes longer—a full afternoon for a typical bed—but the result is a solid, permanent strip that you can drive a mower wheel over without worry. It also looks more finished than metal edging.
Common Mistakes and How to Avoid Them
Most mow strip failures come from a few predictable errors.
- Setting the strip too high: If the strip is more than a half inch above the lawn, the mower deck will hit it, causing scalping or damage. Keep it flush or just barely above.
- Not compacting the base: If you lay pavers directly on loose soil, they will sink unevenly after a few rains. Always compact the base.
- Using edging that is too thin for a riding mower: A thin metal strip will bend under the weight of a large mower. Choose a heavier gauge or use pavers.
- Ignoring the slope: On a slope, water will run along the strip and may wash soil away. Slightly angle the strip or add a small drainage gap at the low end.
- Forgetting to leave room for the mower deck: The strip should be wide enough for the mower wheel (usually a couple of inches), but also leave a few inches of grass on the bed side so the blade can cut it without hitting the strip.
Comparing Materials: Plastic, Metal, Concrete, and Stone
Each material has trade-offs in cost, durability, and installation effort.
- Flexible plastic edging (rolls): Cheap, easy to bend, and simple to install with stakes. It can become brittle in extreme cold and may crack if hit by a mower blade. Best for light-duty, curved edges.
- Rigid metal edging (steel or aluminum): Strong, straight, and long-lasting. More expensive than plastic, and it can rust if scratched (steel) or bend if hit hard. Best for straight edges and moderate mower weight.
- Concrete pavers or bricks: Very durable, heavy, and stable. Installation takes more effort (trenching and leveling), but once set, they rarely move. Best for riding mowers and permanent borders.
- Poured concrete: The most permanent and customizable, but also the most labor-intensive. You need to build forms, mix and pour concrete, and finish the surface. Not recommended as an “easy” method.
- Natural stone (flagstone or cobble): Attractive but expensive and difficult to level. Best for decorative, low-traffic edges where appearance matters more than ease.
Cost and Time Considerations
Costs vary widely by material and yard size, but in general, plastic edging is the least expensive, followed by metal, then pavers, then stone or poured concrete. For a typical bed edge of a few dozen feet, you can expect to spend a modest amount for plastic or metal, and several times that for pavers or stone. Labor time ranges from a couple of hours for hammer-in edging to a full weekend for a paver strip.
If you hire a landscaper, labor will be the largest cost, often exceeding the material cost. Doing it yourself saves that expense and is well within the ability of most homeowners with basic tools (a mallet, a spade, and a level).
Frequently Asked Questions
Can I use a mow strip with a robot mower?
Yes, but you need to check the robot’s specifications. Most robot mowers can cross a flush strip, but a raised strip may confuse the boundary wire or cause the robot to get stuck. A flush paver strip is the safest choice for robot mowers.
How deep should the edging go?
For hammer-in edging, the top should be flush with the soil, and the bottom should be buried deep enough to resist frost heave—usually a few inches. For paver strips, the base should be a couple of inches of compacted sand or gravel, with the paver sitting on top.
Will a mow strip stop all grass from growing into the bed?
No. A mow strip creates a physical barrier that slows rhizome spread, but some aggressive grasses (like Bermuda) can grow under or over the strip. To fully prevent invasion, you may need a deeper vertical barrier or regular edge trimming.
What is the difference between a mow strip and a lawn edging?
Lawn edging is a general term for any border that separates lawn from beds. A mow strip is a specific type of edging designed to support a mower wheel, so it must be wide enough and strong enough for that purpose. Many edging products are purely decorative and cannot support a mower.
Can I install a mow strip over tree roots?
It is best to avoid cutting through large roots. If you have shallow roots, use a hammer-in edging that does not require deep trenching, and place it just to the side of the roots. Cutting major roots can damage the tree.
How do I maintain a mow strip?
For plastic or metal, occasionally check that it is still flush and tap it back down if frost has heaved it. For paver strips, sweep sand into the joints once a year and replace any cracked pavers. Keep the strip free of soil and mulch so the mower wheel rolls smoothly.
Summary
The easiest way to build a mow strip is to choose the method that matches your mower and soil. For most people, hammer-in metal or plastic edging is the fastest and least expensive option, requiring only a mallet and an hour or two of work. For those with a riding mower or a desire for permanence, a paver strip on a compacted base is still a simple DIY project that will last for years. Avoid the common pitfalls of setting the strip too high, skipping the base compaction, or using thin materials, and you will have a clean edge that saves you trimming time every single mow.