Cutting full bricks into thinner, tile-like pieces is a practical way to create custom wall cladding, floor accents, or fireplace surrounds without buying expensive brick veneer. With the right tools and technique, you can turn standard bricks into uniform slices that mimic the look of real masonry at a fraction of the cost. Before you start, you’ll need to choose your brick type—soft clay bricks are easier to cut, while hard engineering bricks may require a more powerful saw. Always wear safety gear, as brick dust and flying chips are hazardous.
What You’ll Need
- Wet saw with a diamond blade (or an angle grinder with a diamond cutting disc)
- Safety glasses and a dust mask (or respirator)
- Hearing protection
- Work gloves
- Straightedge or ruler
- Pencil or chalk for marking
- Water source (for wet cutting) or a spray bottle
- Clamps or a stable workbench
- Brick or stone chisel (if using a hammer-and-chisel method)
- Rubber mallet (for chisel method)
Step-by-Step
- Choose your brick and prepare the work area. Select dry, intact bricks without cracks. Set up your saw or workbench outdoors or in a well-ventilated area. Lay down a tarp to catch slurry if using a wet saw. Make sure you have a stable surface and enough room to handle long bricks.
- Mark the cut line. Measure the desired tile thickness—typically around half an inch to three-quarters of an inch—and mark a straight line across the brick’s face using a pencil and a straightedge. For multiple tiles, mark all bricks before cutting to keep sizes consistent.
- Set up the saw. If using a wet saw, fill the water reservoir and ensure the diamond blade is properly mounted. Adjust the cutting depth so it is slightly deeper than the brick’s thickness. For an angle grinder, attach a diamond cutting disc and have a spray bottle filled with water to cool the blade and reduce dust.
- Make the first cut. Turn on the saw and let the blade reach full speed. Slowly push the brick into the blade, keeping your hands clear of the cutting area. Let the blade do the work—do not force it. If using an angle grinder, clamp the brick securely and guide the disc along the marked line, spraying water to keep dust down.
- Complete the cut. Continue pushing the brick through the blade until the cut is complete. For a wet saw, the brick will come out in two pieces. For an angle grinder, you may need to cut all the way through or score and snap. If the brick is too thick for one pass, make a shallow score line, then deepen it with repeated passes.
- Repeat for additional tiles. Move the brick and make the next cut, leaving a small gap between cuts to account for blade thickness. Keep the brick aligned with the straightedge to ensure uniform thickness.
- Clean up the edges. After cutting, you may notice rough edges or small chips. Use a brick chisel or the saw’s blade to gently smooth them. If you have a rubbing stone or a piece of concrete, you can rub the edges to remove sharp burrs.
- Let the tiles dry. If you used a wet saw, set the tiles aside to dry completely before installation. Damp tiles can affect mortar or adhesive bonding.
Common Mistakes
- Cutting without water. Dry cutting creates massive amounts of dust and can overheat the blade, causing it to dull or warp. Always use water when possible, or at least spray the blade and brick frequently.
- Forcing the blade. Pushing too hard can cause the blade to bind, kick back, or break the brick unpredictably. Let the saw’s weight do the cutting.
- Using the wrong blade. A masonry blade is essential. A wood-cutting blade will shatter or quickly wear out. Diamond blades are designed for brick and stone.
- Not marking accurately. Even a slight angle on the mark will result in uneven tiles. Use a square and a straightedge to ensure your lines are perpendicular to the brick’s face.
- Skipping safety gear. Brick dust contains silica, which is harmful to lungs. Always wear a dust mask and eye protection. Hearing protection is also necessary because saws are loud.
Tips
- Soak the brick before cutting. If you’re using a chisel or an angle grinder, soaking the brick in water for a few minutes can reduce dust and prevent cracking. However, for a wet saw, this is unnecessary.
- Cut in a straight line. For a chisel method, score a deep line on both faces of the brick, then place the chisel on the line and tap firmly with a mallet. The brick should split along the score.
- Work in batches. Cut all your bricks at once to save setup time. Keep the tiles organized by size if you need them for a pattern.
- Use a guide. If you have many cuts to make, clamp a straight piece of wood to the saw table as a fence to ensure consistent width.
- Consider a tile saw. A wet tile saw with a diamond blade is ideal for thin slices. If you don’t own one, many hardware stores rent them by the day.
Troubleshooting
- The brick cracks or shatters. This often happens when the blade is dull, the brick is too hard, or you’re pushing too fast. Slow down, use a new blade, and make sure the brick is firmly supported. If using a chisel, make a deeper score before striking.
- The cut is not straight. Your guide might be loose, or you may have moved the brick mid-cut. Re-mark and re-cut, or use a clamped guide to keep the saw on track.
- The blade gets stuck. Turn off the saw and remove the brick. Check that the blade is aligned and not warped. If the blade is pinching, you may need to cut from the opposite side to meet the first cut.
- Tiles have chipped edges. This is common with brittle bricks. To minimize chipping, use a finer diamond blade and feed the brick slowly. You can also tape the cut line with masking tape to reduce chipping.
- The brick is too thick for the saw. If your saw’s blade cannot cut through the full depth, make a shallow cut on one side, then flip the brick and cut from the other side along the same line.
Frequently Asked Questions
Can I cut brick with a regular circular saw?
Yes, but you need a diamond blade designed for masonry. A standard abrasive blade will wear out quickly and may not cut cleanly. Always use water to cool the blade and control dust.
What is the best tool for cutting brick into tiles?
A wet saw with a diamond blade is the most effective tool because it provides a clean, straight cut and keeps dust down. An angle grinder is a good alternative for smaller jobs, but it requires more skill to keep the cut straight.
How thin can I cut a brick?
You can cut slices as thin as a quarter of an inch, but they become fragile. For most applications, a half-inch to three-quarter-inch thickness is practical and strong enough to handle.
Do I need to seal the cut tiles?
Brick is porous, so sealing is recommended, especially for outdoor or wet areas. Use a masonry sealer after installation to protect against moisture and staining.
Can I cut brick without a saw?
Yes, you can use a hammer and chisel. Score a deep line around the brick, then place the chisel on the score and tap firmly. This method is labor-intensive and less precise, but it works for rough cuts.
How do I cut a brick lengthwise to get a long tile?
Mark a line along the length of the brick, then use a wet saw to cut along that line. You may need to make multiple passes if the brick is thick. Clamp the brick securely to prevent movement.