Yes, you can install greenhouse plastic yourself, and the process is straightforward if you prepare the frame and choose the right materials. The most common method is to drape the film over the hoops or frame, secure one edge, stretch it tight, and fasten it with wiggle wire, locking channel, or greenhouse tape.
Why Plastic Is the Standard Covering
Greenhouse plastic, usually polyethylene film, has replaced glass in many hobby and commercial structures because it is lightweight, inexpensive, and lets in the right amount of light. A single layer of quality film can last several years before UV degradation makes it brittle. Double-layer systems with an inflating fan trap air between two sheets, which adds insulation and can cut heating costs noticeably.
Unlike glass, plastic is flexible enough to bend over curved hoops, which sheds snow and resists wind better than flat panels. It also diffuses sunlight, reducing harsh shadows and the risk of leaf scorch on hot days. For a home gardener, the trade-off is lifespan: plastic needs replacing every few years, while glass or polycarbonate lasts much longer but costs more upfront.
Choosing the Right Film for Your Frame
Not all greenhouse plastic is the same. The two key specs on any roll are thickness, measured in mil, and the UV treatment. A 6-mil film is the most common for hobby greenhouses; it is strong enough for most wind and snow loads but still easy to handle. Thicker film, often 8 mil or more, resists tearing better but is heavier and harder to stretch tight.
UV-treated film is essential. Untreated polyethylene breaks down within a year in direct sun, turning cloudy and then cracking. Look for film that says it is UV stabilized, and note that the treatment is often on the outside layer only, so install the film with the printed side facing out. Some films also have an anti-condensation additive that makes water run down the inside instead of dripping on plants.
For most home greenhouses, a single layer of 6-mil UV-treated film is the best balance of cost and durability. If you live in a cold climate, consider a double-layer system, but know that it requires a small fan to keep the layers inflated.
Tools and Materials You Will Need
Before you start, gather the basics. You will need the plastic film itself, cut a few inches larger than your frame on each side. You will also need a fastening system. The most popular is wiggle wire and locking channel, which is a metal or plastic channel that runs along the frame, with a wavy wire that presses the film into the channel. Another option is greenhouse tape, a wide adhesive strip that sticks to the frame and the film, though it is less secure in high wind.
Other useful items include a helper (the film is awkward alone), a ladder, scissors or a sharp knife, and a wooden batten or rope to temporarily hold the film while you work. If you are using a roll of film, unroll it in the sun for a few minutes first; warm plastic stretches more easily and is less likely to tear.
Step-by-Step Installation Process
The basic process works for most hoop houses and gable frames. Plan for a calm day; wind is your enemy when handling large sheets of plastic.
- Prepare the frame. Cover any sharp edges on the frame with pipe insulation or duct tape. A single burr can tear the film later.
- Drape the film. Unfold the plastic over the top of the frame, letting it hang evenly on both sides. Pull it so the ends overhang equally.
- Secure one end. Start at one gable end. Fold the film over the frame edge, insert the wiggle wire into the channel, and press it down along the entire end. This anchors the film so it cannot slide.
- Stretch the sides. Move to the opposite end and pull the film tight lengthwise. Work from the center outward, pulling the film down and outward to remove wrinkles.
- Fasten the sides. Starting at the middle of one side, press the film into the locking channel with the wiggle wire. Work toward the corners, pulling the film taut as you go. Repeat on the other side.
- Trim and finish. Cut off excess film with a sharp knife, leaving a couple of inches beyond the channel. Fold the excess over the channel and tape it down to keep water out.
If you are covering a large greenhouse, you may need to work in sections, overlapping seams by at least a foot and sealing them with special repair tape designed for greenhouse film.
Common Problems and How to Avoid Them
The most frequent mistake is installing the film too loose. A loose film flaps in the wind, which wears it out quickly and can tear it at the fastening points. Pull the film as tight as you can by hand, and consider using a come-along or ratchet strap for large structures to get a drum-tight finish.
Another issue is chafing where the film touches the frame. Even with smooth hoops, the constant rubbing in wind can wear a hole. Use pipe insulation on the hoops, or add a strip of old carpet or felt where the film rests. Also, do not overtighten the wiggle wire; it should hold the film firmly but not cut into it.
Condensation is a third problem. On cold nights, moisture forms on the inside of the plastic and drips onto plants, which can spread fungal diseases. An anti-drip film helps, but you can also improve airflow with vents or a small fan. If you see water pooling on top of the film, that is a sign the frame is sagging; tighten the film or add a support brace.
Costs and Lifespan Considerations
The price of greenhouse plastic varies with thickness, width, and UV treatment. A 6-mil film for a small hobby greenhouse typically costs less than several panels of glass, but the real cost is in replacement. Most quality films last between two and four years in full sun, depending on how much UV exposure they get and how tight they are installed.
A double-layer system costs more upfront because you buy two sheets and a small inflation fan, but the trapped air can reduce heat loss by a significant amount in winter. For a gardener who heats their greenhouse, the fan pays for itself in lower energy bills over a couple of seasons. For an unheated structure, a single layer is usually enough.
When comparing to other coverings, note that polycarbonate panels last many years and insulate well, but they cost several times more per square foot. Glass is the most attractive and longest lasting, but it is heavy, fragile, and requires a stronger frame. Plastic is the right choice when budget and ease of installation matter more than longevity.
Safety and Maintenance Tips
Working with large sheets of plastic has a few hazards. The film is slippery when folded, so wear shoes with good grip and never climb on the frame while holding the plastic. Use a sturdy ladder, and have a helper hold the ladder while you work at height. Cut the film with a sharp blade, but always cut away from your body and keep your fingers clear of the cutting line.
Once installed, inspect the film a few times a year. Look for small tears or holes, especially near the fastening channels and corners. Repair them early with greenhouse repair tape; a small patch lasts for months, but a tear that is left alone will rip across the whole sheet in a strong wind. In heavy snow, brush the top of the greenhouse gently to prevent the weight from collapsing the frame. Do not use a sharp shovel; a soft broom or a leaf blower is safer.
Frequently Asked Questions
Can I install greenhouse plastic over an existing frame without removing the old film? It is not recommended. The old film will trap moisture between the layers, which promotes mold and makes the new film sag. Remove the old plastic completely, clean the frame, and then install the new sheet.
Which side of the film faces out? Most greenhouse films have a UV treatment on one side only. The treated side should face the sun. The film usually has a printed line or label on the inside; if you can see the print from outside, the film is on backwards.
How do I fix a tear in the middle of the sheet? Clean the area with a dry cloth, then apply a piece of greenhouse repair tape that is at least twice the size of the tear. Press it down firmly and smooth out air bubbles. For a large rip, you may need to patch both sides of the film.
Is it better to use clear or white plastic? Clear film lets in the most light, which is best for growing most vegetables and flowers. White or opaque film diffuses light more, which reduces heat buildup in summer but also reduces the total light available. Choose clear for spring and fall growing, and consider shade cloth over clear film for hot summer months.
Can I install plastic on a greenhouse that is not a perfect hoop shape? Yes, the same method works on gable, A-frame, and even lean-to structures. The key is to have a continuous surface to fasten the film to. If your frame has sharp corners, pad them well and consider using a wider locking channel to spread the stress.