This guide covers the most reliable ways to keep screws from backing out over time, whether you’re working on furniture, a deck, a vehicle, or household appliances. Vibration, temperature changes, and everyday use all work against a screw’s grip, but a few simple techniques and the right hardware can make a joint stay tight for years. Before you start, you’ll need to identify what kind of screw you’re dealing with (wood screw, machine screw, or self-tapping screw) and what material it’s going into, because the best solution differs for wood, metal, and plastic.
What You’ll Need
- Correct-size screwdriver or bit (Phillips, flathead, Torx, or hex)
- Thread-locking adhesive (blue for removable, red for permanent)
- Wood glue or epoxy (for wooden joints)
- Toothpicks or wooden matchsticks (for stripped wood holes)
- Wire or plumber’s tape (for metal threads)
- Rubber band or steel wool (for stripped screw heads)
- Pilot drill bit (slightly smaller than the screw’s core)
- Hammer and a small nail or awl (to start a pilot hole)
- Clean rag and rubbing alcohol (to degrease threads)
Step-by-Step
- Clean the threads and the hole. Any grease, oil, or old thread-locker will prevent a fresh bond. Wipe the screw threads with a rag dipped in rubbing alcohol and let them dry completely. For the hole, blow out dust or use a cotton swab. This step is critical for adhesives to work.
- Choose the right fix for the material. For wood, you’ll typically use glue or a larger screw. For metal, use a thread-locking adhesive or a mechanical lock (like a lock washer or a second nut). For plastic, you might need a slightly larger screw or a thread-forming screw that cuts deeper.
- For wood screws in softwood or hardwood: Apply a small drop of wood glue to the screw threads before driving it in. The glue fills the microscopic gaps between the threads and the wood fibers, creating a much stronger grip. Wipe off any excess glue that squeezes out. This is a simple, effective method for furniture and indoor projects.
- For wood screws in a stripped hole: Remove the screw, push a couple of toothpicks coated in wood glue into the hole, break them off flush, and let the glue dry. Then re-drive the screw. The toothpicks act as new wood for the threads to bite into. For larger holes, use wooden dowels cut to length and glued in.
- For metal machine screws: Apply a drop of thread-locking adhesive to the threads (not the head) before assembly. Blue thread-locker is removable with hand tools; red is permanent and requires heat to break. Use only a drop or two—more doesn’t help and can make a mess. Tighten to the specified torque if you have a manual.
- For metal screws in vibration-heavy applications (like a car engine or lawn mower): Use a mechanical lock instead of, or in addition to, an adhesive. Options include a split lock washer, a star washer, or a serrated flange nut. For bolts, a second nut (jam nut) tightened against the first creates a very secure lock. For screws, a nylon-insert lock nut works well.
- For screws in plastic: The best fix is to use a screw that’s slightly larger in diameter, or a self-tapping screw that cuts new threads. If you can’t change the screw, apply a small amount of super glue or epoxy to the threads and drive it in quickly. Be careful not to overtighten, as plastic can crack.
- For any screw that keeps loosening due to vibration: Consider adding a spring washer (also called a split washer) between the screw head and the surface. This washer keeps tension on the threads even when the material compresses or settles. It’s a cheap, effective solution for many mechanical assemblies.
- For a stripped screw head (the driver keeps slipping): Place a wide rubber band over the screw head, then press the screwdriver into it and turn. The rubber fills the stripped recess and gives you grip. Alternatively, use a screw extractor kit, which grips the head from the outside. If the head is completely rounded, you may need to drill it out.
Common Mistakes
- Using too much thread-locker. A drop is enough. Excess can run into the joint and cause corrosion or make removal nearly impossible.
- Overtightening. This strips the threads in wood or plastic, making the problem worse. Tighten until snug, then a quarter turn more for most applications.
- Ignoring the pilot hole. In hardwoods and metal, a pilot hole prevents the screw from breaking and ensures the threads cut properly. Without it, the screw may not seat fully.
- Using a lock washer on a screw that already has a serrated flange. The flange does the job; adding a washer can actually reduce contact and loosen over time.
- Applying thread-locker to a dirty or oily screw. It won’t bond, and you’ll think the product failed when it was the surface prep.
- Forgetting to let glue dry before re-tightening. If you torque the screw while the glue is still wet, you push the glue out and the bond is weak.
Tips
- For outdoor projects, use galvanized or stainless steel screws to avoid rust, which can cause the screw to seize or weaken the joint.
- If you’re assembling furniture that will be disassembled later (like a bed frame), use a removable thread-locker (blue) and never glue the screw.
- For high-vibration environments, check the tightness after the first few uses. Re-tighten and then apply a thread-locker if needed.
- Mark the screw head and the surface with a small paint dot after tightening. If the dot misaligns, you know it’s loosening.
- When driving screws into particleboard or MDF, use screws specifically designed for those materials—they have a different thread angle and grip better.
- For metal, a drop of oil on the threads before assembly can reduce friction and allow you to tighten more accurately, but it can also reduce the holding power of thread-locker, so skip oil if you’re using adhesive.
Troubleshooting
The screw still loosens after using thread-locker. You likely applied it to a dirty surface or used the wrong type. Clean with alcohol, apply a fresh drop, and let it cure for the recommended time (usually a few hours) before putting the part into service. If it still fails, switch to a mechanical lock.
The screw head is stripped and you can’t get it out. Use a rubber band as described in step 9. If that fails, use a screw extractor: drill a small hole into the screw head, tap in the extractor, and turn counterclockwise. If the screw is in wood, you can also try gripping the head with locking pliers and turning.
The wood hole is too large for a new screw. Glue in a wooden dowel, let it dry, cut it flush, and drill a new pilot hole. For a quick fix, wrap the screw threads with a bit of steel wool or wire before driving—this fills the gap, but it’s not a permanent solution.
The screw breaks off flush with the surface. This is tricky. For metal, you may need to drill it out and use a larger screw. For wood, you can carefully drill a small hole into the broken screw and use a screw extractor. If that fails, it’s often easier to drill out the entire screw and fill the hole with a dowel.
Thread-locker is too strong and you can’t remove the screw. Apply heat with a heat gun or soldering iron to the screw head for a minute or two. The heat breaks the bond. Be careful with plastic or painted surfaces.
The screw loosens because the material is soft (like drywall or foam). Use a special anchor designed for that material, or switch to a screw with a coarser thread. For drywall, use a drywall anchor. For foam, use a screw with a wider thread pitch.
Frequently Asked Questions
Q: Can I use super glue instead of thread-locker?
A: Yes, in many cases. Super glue (cyanoacrylate) works well on metal and plastic, but it’s brittle and can crack under vibration. For wood, wood glue is better because it’s flexible. Thread-locker is specifically formulated for metal threads and is the safer bet.
Q: How do I know if a screw is loose because of vibration or just poor installation?
A: If the screw loosens within days of installation, it’s likely poor installation (wrong pilot hole, overtightened, or stripped). If it loosens after weeks or months of use, it’s usually vibration or thermal cycling. Check the threads for wear—if they’re shiny or worn, it’s vibration.
Q: Will a larger screw always fix a stripped hole?
A: Not always. If the hole is stripped in wood, a larger screw can help if the surrounding wood is solid. But if the wood is cracked or rotted, a larger screw won’t hold. You need to repair the wood first.
Q: Is it okay to use a lock washer on a wood screw?
A: A lock washer is designed for metal-to-metal connections. On wood, it can actually damage the surface and doesn’t provide much benefit. For wood, use glue or a screw with a built-in washer head.
Q: What’s the difference between blue and red thread-locker?
A: Blue is medium strength and removable with hand tools. Red is high strength and requires heat to remove. For most household items, blue is sufficient. Red is for permanent assemblies like engine components.
Q: Can I use thread-locker on plastic screws?
A: Some thread-lockers can weaken certain plastics. Check the product label for compatibility. For plastic, a better option is to use a screw with a finer thread or a thread-forming screw that cuts deeper.