A wood door usually sticks because it has swollen with humidity, shifted slightly in its frame, or developed a rough spot where it rubs. Find the contact point first, then try the least invasive fix; avoid trimming the door until you have ruled out loose hardware and seasonal swelling.
This guide applies to typical interior and exterior wood doors. Work slowly and keep the door supported when adjusting hinges or removing it. If the door is fire-rated, part of a security system, or under warranty, check its requirements before altering it.
What You’ll Need
- Flashlight and pencil
- Phillips or flat-head screwdriver that fits the hinge screws
- Wedge or doorstop to keep the door steady
- Fine sandpaper and a sanding block
- Wood finish or paint for protecting any newly exposed wood
- Optional: thin card or paper, a plane, and a suitable dry lubricant for hinges
- Safety glasses and a dust mask if sanding or planing
Use a screwdriver rather than a drill for small hinge adjustments so you are less likely to strip a screw or overtighten it. If you need to remove the door, have another person help support it.
Step-by-Step
- Check when and where it sticks. Open and close the door slowly, without forcing it. Notice whether the resistance happens throughout the swing or only near the latch, top, bottom, or hinge side. Try again at a different time of day if the problem varies with damp or dry weather. A door that rubs only in humid conditions may have swollen temporarily; a persistent rub in the same place can point to misalignment or a high spot.
- Locate the contact point. Look for fresh scuffs, compressed paint, shiny patches, or wood dust along the door edge and frame. If the mark is hard to see, slide a thin strip of paper between the door and frame while closing it gently. Where the paper catches or tears is a useful clue. Check the floor and the top edge too, but do not push the door hard against the frame.
- Check the hinges and screws. With the door open, look for loose screws, a hinge leaf pulling away from the jamb, bent hinge parts, or a cracked area of wood. Tighten loose screws carefully, keeping the screwdriver aligned with the screw head. Do not keep turning a screw that spins without tightening; the hole may be damaged. If a hinge is visibly bent or the jamb is split, stop and repair that problem rather than sanding the door to compensate.
- Test for hinge-side sag. A door that drops can rub at the upper latch corner or along the lower hinge-side edge. With the door partly open, gently lift the handle side while watching the hinges. Noticeable movement may mean a loose hinge, worn hinge pin, or damaged screw holes. Tighten accessible screws first. If a screw hole no longer grips, a secure repair may require removing the hinge and restoring the hole with an appropriate wood repair method before reinstalling the screw. Avoid relying on a longer screw unless you know what is behind the jamb.
- Look for a seasonal moisture problem. If the door swells during damp weather but moves freely when conditions are drier, wait for conditions to stabilize before removing wood. Keep indoor humidity reasonably steady where practical, and address obvious sources of moisture such as a leak or poor ventilation. Do not sand a swollen door aggressively: once it dries, the reduced edge may leave an excessive gap.
- Try a small hinge adjustment before removing wood. If the hinges are sound and the door is slightly out of position, tighten their screws and check the fit again. A loose hinge can often account for a rub at the top or latch side. Use only adjustments supported by the hinge design; do not bend hinge leaves or force pins as a quick fix. Close the door gently after each change to see whether the clearance has improved.
- Remove a small high spot only if needed. If the door still catches at a clearly identified wood-on-wood spot and the frame and hinges are sound, mark the area with a pencil. Take the door off only if you can support it safely. Sand or plane a very small amount from the marked edge, keeping the tool flat and working with the grain where possible. Refit the door and test it before removing more. For a painted door, take care not to damage surrounding paint or create a sharp, uneven edge.
- Seal exposed wood and check the latch. Bare wood can take up moisture, so protect any trimmed area with a compatible primer, paint, or finish after preparing it according to the product directions. Let it dry fully before closing the door against the frame. Then check that the latch enters the strike plate freely and that the door stays closed without being pushed or pulled into place.
Common Mistakes
- Sanding before diagnosing the cause: Removing wood will not fix a loose hinge, bent hardware, or a shifted frame. It can also leave a permanent gap after seasonal swelling passes.
- Forcing the door: Repeatedly pushing or pulling can damage the latch, hinge screws, finish, or frame. Stop when you feel firm resistance and identify the rub.
- Removing too much material: A small change can affect the reveal around the door. Work in gradual passes, reinstalling and testing between them.
- Leaving raw wood exposed: An unsealed edge may absorb moisture and become rough or swollen again. Apply an appropriate finish once the fit is correct.
- Using oil indiscriminately: A lubricant may help a noisy hinge, but it will not correct a door that physically rubs. Excess oil can attract dirt or mark nearby surfaces; use a product suited to the hinge and apply sparingly.
- Overtightening screws: Excess force can strip the screw head or damage the wood. Stop if a screw will not turn normally or does not become snug.
Tips
- Keep a note of where the door catches and whether the problem changes with weather. That distinction helps separate temporary swelling from a lasting alignment issue.
- Use a flashlight at a shallow angle to spot rubbing marks and uneven gaps. Compare the space around the door on the hinge and latch sides.
- Make one change at a time. After tightening a screw or sanding a small area, test the door before doing anything else.
- Protect the floor and nearby surfaces before sanding. Collect dust rather than letting it settle on the hinge or latch mechanism.
- If the door is difficult to lift, remove, or hold safely, do not work alone. A supported door is less likely to fall or twist while its hinges are being handled.
Troubleshooting
The door still rubs after tightening the hinges: Recheck the exact contact point. A hinge may be worn or bent, or the frame may have moved. If the door is visibly out of square, the jamb is damaged, or the gap is uneven in several places, hinge tightening alone may not solve it. Have a carpenter assess the alignment before trimming the door.
The door sticks only in damp weather: Avoid permanent material removal while the door is swollen. Check for moisture sources and allow conditions to settle. If the door remains tight after the weather changes, inspect the hinges and frame again.
A screw turns but will not tighten: The hole may be stripped or the wood may be damaged. Do not keep spinning the screw or use a larger fastener without checking what lies behind the jamb. Repair the hole appropriately, or ask a carpenter if the hinge carries a heavy door.
The latch catches even though the edges do not rub: The strike plate and latch may be misaligned. Look for a worn mark on the plate, then check whether the door sags or whether the latch itself moves freely. Correct the cause of the misalignment before enlarging the strike opening.
The door scrapes the floor: Check for sagging hinges and loose screws first. If the floor covering has changed or the threshold has shifted, trimming the door may not be the right repair. A door that is heavy, glazed, or part of a rated assembly should be handled by a qualified professional.
Frequently Asked Questions
Why does a wood door stick when the weather is humid?
Wood can take up moisture and expand, reducing the clearance between the door and its frame. If the problem is seasonal, wait for conditions to become more stable before removing material.
Can I use soap or candle wax on a sticking door?
These may reduce friction at some contact points, but they do not fix sagging hinges or swollen wood and can leave residue. Identify the cause first; reserve a suitable hinge lubricant for a squeaky hinge, not a rubbing door edge.
Should I sand the door or adjust the hinges first?
Check and tighten sound, accessible hinge screws before sanding. Removing wood is permanent, while correcting a loose hinge may restore the door’s position without changing its size.
How can I tell if the door is sticking because it has sagged?
Look for rubbing near the upper latch corner, an uneven gap, or movement when you gently lift the handle side with the door partly open. Loose, worn, or damaged hinges can cause sagging and should be addressed before trimming.
Will a sticking door fix itself?
It may move freely again if temporary humidity-related swelling subsides. A loose hinge, damaged frame, or persistent rub is unlikely to correct itself, so inspect the hardware and contact point.
When should I call a carpenter?
Get help if the frame is cracked or visibly out of square, a hinge is bent, screw holes are badly damaged, or the door is heavy or safety-rated. Professional assessment is also sensible when the cause is unclear and the proposed repair would remove substantial material.