Grease Stains on Concrete: How to Remove Them

Grease stains on a concrete driveway, garage floor, or patio are stubborn and unsightly, but they are not permanent. With the right approach and a little patience, you can lift most of the oil and leave the concrete looking clean. The key is to act quickly, use an absorbent material, and follow up with a degreaser and a stiff brush. This guide walks you through the process step by step, from fresh spills to old, set-in stains.

What You’ll Need

  • Absorbent material: cat litter, baking soda, cornstarch, or sawdust
  • A stiff-bristle brush (a push broom or a scrub brush works)
  • A degreaser: a commercial concrete degreaser, or a homemade mix of dish soap and warm water
  • A bucket of hot water
  • A hose or a few gallons of water for rinsing
  • Plastic sheeting or a trash bag (to cover the area if rain is expected)
  • Protective gloves and safety glasses (for handling chemicals)
  • For old stains: a poultice (a paste of an absorbent and a solvent) and a scraper or putty knife

Step-by-Step

  1. Act fast if the spill is fresh. The sooner you address a grease spill, the easier it is to remove. As soon as it happens, cover the spot generously with an absorbent material like cat litter, baking soda, or cornstarch. Use enough to create a layer about half an inch thick. Let it sit for at least an hour, or overnight if possible. The absorbent will draw the oil out of the concrete pores.
  2. Sweep up the absorbent. After it has sat, sweep up the absorbent material. You should see that it has darkened with the absorbed grease. Dispose of it in the trash—do not compost it or wash it down a drain.
  3. Scrub with a degreaser. Apply a commercial concrete degreaser according to the product’s instructions, or make a paste of dish soap and warm water. Use a stiff-bristle brush to work the degreaser into the stain. Scrub in a circular motion, applying firm pressure. Let the degreaser sit for ten to fifteen minutes to break down the grease.
  4. Rinse thoroughly. Rinse the area with a hose or with buckets of water. If the stain is gone, you are done. If not, repeat the degreaser step. For a stubborn stain, you may need to let the degreaser sit longer (up to an hour) and scrub again.
  5. For old or set-in stains, use a poultice. Mix an absorbent (like baking soda or a commercial poultice powder) with a solvent (like a commercial degreaser or a citrus-based cleaner) to form a thick paste. Apply the paste over the stain in a layer about half an inch thick. Cover it with plastic sheeting to slow evaporation and let it sit for twenty-four to forty-eight hours. The paste will slowly draw the grease out of the concrete. Then scrape it off and rinse.
  6. Repeat if necessary. Some stains, especially old ones, may require several treatments. Be patient—each cycle lifts a little more oil. Between treatments, let the concrete dry completely before reapplying.
  7. Clean up and prevent future stains. Once the stain is gone, rinse the area well and let it dry. To prevent future stains, consider sealing your concrete with a concrete sealer, which creates a barrier that makes it easier to clean spills. Also, place a drip pan or a piece of cardboard under vehicles that may leak oil.

Common Mistakes

  • Using water on a fresh spill. Water spreads the grease and pushes it deeper into the concrete. Always blot or absorb first, never rinse.
  • Scrubbing too hard with a wire brush. A wire brush can scratch the concrete and make the stain worse. Use a stiff-bristle brush (nylon or natural) instead.
  • Using a pressure washer too soon. A pressure washer can force grease deeper into the pores. Use it only after you have lifted most of the oil with absorbents and degreasers.
  • Not letting the absorbent sit long enough. Give the absorbent time to work—at least an hour, but overnight is better. Rushing this step leaves oil behind.
  • Using bleach or ammonia. These are not effective on grease and can damage the concrete or create harmful fumes. Stick to degreasers and absorbents.
  • Ignoring the weather. If rain is forecast, cover the area with plastic sheeting. Rain can wash away your treatment and spread the stain.

Tips

  • Test a small area first. Before applying any chemical to the whole stain, test it on a small, inconspicuous spot to make sure it does not discolor or damage the concrete.
  • Use a degreaser designed for concrete. Many hardware stores sell concrete-specific degreasers that are more effective than general-purpose cleaners.
  • For a homemade poultice, try baking soda and water. Make a thick paste and apply it as described. It is gentle and works well on light stains.
  • If the stain is on a driveway, park a car over it? No, that is a bad idea—the weight can push the grease deeper. Instead, work on it when the area is clear.
  • Seal your concrete after cleaning. A good sealer will make future spills much easier to wipe up. Reapply the sealer every few years as recommended by the manufacturer.
  • For a very large stain, consider a commercial concrete cleaner. Some products are designed to be spread over a large area and scrubbed with a floor machine. If you have a big spill, you may want to rent a floor buffer.

Troubleshooting

The stain is still visible after several attempts. This is common with old, deeply set stains. The oil has penetrated deep into the concrete pores. Continue with poultice treatments—each one will draw out a little more. It may take several cycles over a few weeks. If the stain is truly stubborn, you can try a stronger commercial poultice or a concrete cleaner that contains a solvent. Always follow the manufacturer’s instructions and test in an inconspicuous area first.

The degreaser leaves a white residue. This can happen with some commercial products. Rinse the area thoroughly with water, and if the residue persists, scrub with a mild acid solution (like a mixture of water and white vinegar) and rinse again. Be careful with acid—it can etch the concrete if left too long.

The stain reappears after it rains. This indicates that some oil is still deep in the concrete and is being drawn to the surface by water. Repeat the poultice treatment, and consider sealing the concrete once the stain is gone to prevent moisture from wicking oil up.

The concrete is discolored after cleaning. Some degreasers can lighten or darken concrete. If the color is off, wait a few days—it may even out as the concrete dries. If it does not, you may need to apply a concrete color restorer or sealer.

The stain is on a porous or decorative concrete surface. If your concrete is stamped, colored, or has a broom finish, be extra careful. Harsh chemicals can damage the surface. Use a mild dish soap solution first, and test any product in a hidden area. For decorative concrete, consider consulting a professional.

Frequently Asked Questions

Can I use a pressure washer to remove grease stains? Yes, but only after you have absorbed the bulk of the oil with an absorbent and treated the stain with a degreaser. A pressure washer can help rinse away the degreaser and any remaining surface oil, but using it on a fresh spill will push grease deeper into the concrete.

Does baking soda work on grease stains? Yes, baking soda is an excellent absorbent for fresh spills. Sprinkle it on generously, let it sit, and sweep it up. For older stains, you can make a paste of baking soda and water and apply it as a poultice.

How long does it take to remove a grease stain? It depends on the age and size of the stain. A fresh spill can often be removed in a few hours with absorbents and a degreaser. An old, set-in stain may take several days or weeks of repeated poultice treatments. Patience is key.

Will kitty litter work? Yes, clay-based cat litter is a great absorbent for fresh spills. It is cheap and effective. Just make sure it is non-clumping, as clumping litter can turn into a gooey mess when wet.

Is it safe to use a commercial degreaser on concrete? Most commercial concrete degreasers are safe when used as directed. Always wear gloves and safety glasses, work in a well-ventilated area, and test on a small spot first. Some degreasers contain acids or solvents that can etch or discolor concrete if left on too long.

Should I seal my concrete after removing the stain? Yes, sealing is a good idea. A sealer creates a protective barrier that makes it easier to clean future spills and prevents stains from penetrating. Choose a sealer that is appropriate for your concrete type and follow the manufacturer’s application instructions.