How to Fix Drywall Nail Pops

Drywall nail pops are small, circular bumps or cracks that appear where a nail or screw holding drywall to the framing has pushed through the paper surface. They are common in homes as wood framing expands and contracts with humidity changes, or when the fastener was not driven deep enough. Fixing them is a straightforward DIY job that takes about an hour per pop, and the result is a smooth wall ready for paint.

What You’ll Need

  • Hammer or screwdriver (depending on whether you have nails or screws)
  • Drywall screws (1¼-inch or 1⅝-inch, coarse thread for wood studs)
  • Drywall knife (4-inch or 6-inch)
  • Joint compound (also called mud)
  • Sandpaper or sanding sponge (medium and fine grit)
  • Utility knife or box cutter
  • Putty knife or small scraper
  • Primer and paint (to match the wall)
  • Dust mask and safety glasses
  • Drop cloth or plastic sheeting

Step-by-Step

  1. Prepare the area. Lay down a drop cloth to catch dust and debris. Put on your dust mask and safety glasses. If the wall has wallpaper or a textured finish, you may need to score around the pop with a utility knife to prevent tearing the surface further.
  2. Remove the popped nail or screw. If it is a nail, use a hammer to gently tap it back in? but not all the way. If it is a screw, use a screwdriver or drill to remove it completely. For nails, you can either pull them out with a pry bar or hammer claw, or if they are still holding, you can drive a new screw next to them. The goal is to eliminate the loose fastener.
  3. Drive a new screw. Place a new drywall screw about an inch above or below the old pop, directly into the same stud. Drive it so the head is just below the paper surface? but not so deep that it breaks the paper. The dimple should be about the size of a dime. If you are using a screwdriver, set the clutch so it stops at the right depth.
  4. Set the old nail (if you chose to keep it). If you kept the original nail, hammer it back in so the head is slightly below the surface, creating a small dimple. If the nail is too loose to hold, remove it and use only the new screw.
  5. Fill the dimples with joint compound. Using a drywall knife, apply a thin layer of joint compound over both the new screw dimple and the old nail hole (if any). Press firmly to fill the depression completely. Scrape off the excess so the compound is flush with the wall surface. Let it dry completely (usually a few hours, but follow the product instructions).
  6. Sand the area. Once dry, sand the compound smooth with medium-grit sandpaper or a sanding sponge. Use a light touch to avoid gouging the paper. Wipe away the dust with a damp cloth.
  7. Apply a second coat (if needed). For most pops, one coat is enough, but if you can still see a depression or the compound shrank, apply a second thin coat and let it dry. Sand again lightly.
  8. Prime and paint. Before painting, apply a coat of primer over the repaired area. This seals the compound and prevents the paint from flashing (looking shiny). Once the primer is dry, paint the entire wall to match. If you only paint the spot, it will be noticeable, so plan to repaint the whole wall or at least the section from corner to corner.

Common Mistakes

  • Not using a new screw. Some people just hammer the nail back in and fill the hole. That sets you up for a repeat pop because the nail will loosen again with the next humidity change.
  • Driving the screw too deep. If the screw breaks the paper, it loses holding power and you will get a new pop. The screw head should be just below the surface, not buried.
  • Using too much joint compound. A thick glob takes forever to dry and shrinks as it dries, leaving a depression. Thin coats are better.
  • Skipping the primer. Joint compound is porous. If you paint directly over it, the paint will dry duller than the rest of the wall. Primer seals it and gives an even finish.
  • Sanding too aggressively. Sanding through the paper can create a bigger problem. Use light pressure and check frequently.

Tips

  • Check for multiple pops. If you have one nail pop, there are likely others nearby. Run your hand over the wall to feel for bumps or look for cracks. Fix them all at once.
  • Use screws instead of nails for new work. Screws hold drywall much better than nails and are less likely to pop. If you are doing a full drywall job, use screws.
  • Match the screw length. For ½-inch drywall on wood studs, use 1¼-inch screws. For ⅝-inch drywall, use 1⅝-inch screws. Too short a screw won’t bite into the wood; too long may poke through the other side.
  • Let the compound dry fully. Rushing the drying time leads to cracks. Check the label for recommended drying time, and wait a bit longer if the humidity is high.
  • Keep a small container of compound. You do not need a whole bucket. A small tub or even a plastic container with a lid works fine for a few pops.

Troubleshooting

The screw won’t go in. If you hit a hard spot in the stud, the screw may bend or break. Try moving the screw an inch up or down. If the stud is metal, you will need a self-tapping drywall screw, but that is rare in residential walls.

The paper is torn. If the drywall paper is ripped, you need to repair that first. Cut away loose paper with a utility knife, then apply a thin layer of joint compound, let it dry, sand, and then proceed with the screw. If the tear is large, you may need to cut out the damaged section and patch with a new piece of drywall.

The pop keeps coming back. This usually means the fastener is not holding. If you used a screw and it still pops, the stud may be warped or the drywall may be too damaged. Try a longer screw (but not so long it goes through the other side) or add a second screw a few inches away.

The joint compound cracks. Cracks usually mean the compound was applied too thick or the surface was not clean. Sand the area, remove dust, and apply a thinner coat. If the crack is along the seam, you may have a deeper issue with the tape.

Paint doesn’t match. Even with primer, the repaired spot may look different because the wall has aged or the paint sheen is different. The only reliable fix is to repaint the entire wall. If you have leftover paint, use it; if not, take a chip to a paint store for color matching.

Frequently Asked Questions

Can I just hammer the nail back in? Yes, but it will likely pop again because the nail is still loose in the wood. A new screw is the permanent fix.

Do I need to remove the old nail? Not necessarily. If you can hammer it back in and it holds, you can leave it and just add a screw nearby. But if it is too loose, pull it out.

How long does the joint compound take to dry? It depends on the product and humidity. Lightweight compounds dry in a few hours, but it is best to wait overnight before sanding.

Can I use spackle instead of joint compound? Yes, for small nail pops, spackle works fine and dries faster. Just make sure it is sandable.

Will nail pops come back after I fix them? If you use a screw and the framing is stable, they should not. But if your house has ongoing humidity swings or settling, new pops can appear elsewhere.

Do I need to prime before painting? Yes, primer seals the joint compound and prevents the paint from flashing. Skipping it can leave a dull spot that is hard to fix.