How to Fix a Dripping Tap: Step-by-Step Guide

A dripping tap is more than an annoyance—it can waste a surprising amount of water over time and add a few cents to your water bill. The good news is that most dripping taps are caused by a worn-out washer or O-ring, and fixing it is a straightforward DIY job that takes less than an hour. With a few basic tools and a little patience, you can stop the drip and save water.

What You’ll Need

  • Adjustable wrench or spanner
  • Flat-head and Phillips screwdrivers
  • Replacement washers or O-rings (match the size and type to your tap)
  • Plumber’s tape (thread seal tape)
  • White vinegar or a mild descaler (for cleaning)
  • Clean cloth or rag
  • Bucket or bowl to catch water
  • Penetrating oil (if parts are stuck)

Step-by-Step

  1. Turn off the water supply. Locate the isolation valve under the sink or the main water shut-off valve for your home. Turn it clockwise to close. Open the tap to release any remaining water and confirm the water is off.
  2. Plug the drain. Place a stopper or a cloth in the sink to prevent small parts from falling down the drain.
  3. Remove the tap handle. Look for a small screw on the top or side of the handle. It may be hidden under a decorative cap—pry it off gently with a flat-head screwdriver. Unscrew and lift the handle off. If it’s stuck, wiggle it gently or use a penetrating oil.
  4. Unscrew the cap or bonnet. Under the handle, you’ll see a metal cap or bonnet that holds the internal cartridge or valve. Use an adjustable wrench to unscrew it counterclockwise. If it’s tight, wrap the jaws with tape to avoid scratching.
  5. Remove the cartridge or valve stem. Pull the cartridge straight out. It may be held by a clip or a screw—remove those first. If it’s stubborn, twist it gently while pulling.
  6. Inspect the washer and O-ring. Look at the rubber washer at the bottom of the cartridge and the O-ring around it. If they are worn, cracked, or misshapen, that’s the cause of the drip.
  7. Replace the washer and O-ring. Take the old parts to a hardware store to match the size, or use a multi-pack of common sizes. Push the new washer into place and slide the new O-ring over the cartridge. Ensure they sit snugly.
  8. Clean the valve seat. While the cartridge is out, wipe the inside of the tap body with vinegar to remove mineral deposits. If the valve seat (the flat surface where the washer meets) is rough, you can polish it with a fine abrasive pad—but be gentle.
  9. Reassemble in reverse order. Put the cartridge back, tighten the cap with your wrench (don’t over-tighten—just snug), replace the handle, and secure the screw.
  10. Turn the water back on. Slowly open the shut-off valve. Check for leaks around the handle and base. Turn the tap on and off a few times to ensure smooth operation and no dripping.

Common Mistakes

  • Not turning off the water properly. If you only close the tap itself, water will still flow when you disassemble. Always use the isolation valve or main shut-off.
  • Over-tightening. Crank down on the cap or handle and you can crack the ceramic disc or strip threads. Hand-tighten, then give a quarter turn with the wrench.
  • Using the wrong washer size. A washer that’s too big won’t seat properly; one that’s too small will leak. Match it exactly or use a universal kit.
  • Skipping the O-ring. Even if the washer looks fine, a worn O-ring can cause a drip around the handle. Replace both while you’re in there.
  • Forgetting to clean the valve seat. Mineral buildup can prevent a tight seal even with a new washer. A quick wipe with vinegar helps.

Tips

  • Take photos before disassembling. A quick photo of the parts in order will save you confusion during reassembly.
  • Use plumber’s tape on threads. Wrap a few turns of tape around the threads of the cap to ensure a watertight seal and make future removal easier.
  • Buy a multi-pack of washers. They’re cheap and you’ll have the right size on hand for other taps.
  • If the tap is a ceramic disc type, don’t replace washers. Instead, clean the disc or replace the whole cartridge—it’s simpler and more reliable.
  • Work slowly and keep parts organized. Lay them out on a towel in the order you removed them.

Troubleshooting

  • Water still drips after replacing the washer. The valve seat may be pitted or rough. Use a valve seat dressing tool to smooth it, or replace the entire cartridge if it’s a modern tap.
  • Handle is hard to turn. The new O-ring might be too thick, or the cartridge isn’t seated properly. Remove and reseat, ensuring it’s aligned.
  • Leak at the base of the handle. Usually a worn O-ring on the cartridge or a loose packing nut. Tighten gently or replace the O-ring.
  • Tap is still dripping after a few days. The washer may have been damaged by a rough valve seat. Recheck the seat and polish it if needed.
  • Can’t get the handle off. Apply penetrating oil and wait a few minutes. If it’s still stuck, gently tap the side with a wrench handle—but be careful not to damage the finish.
  • Water pressure seems lower after reassembly. You might have installed the cartridge upside down or the water supply is partially closed. Check both.

Frequently Asked Questions

Why does my tap keep dripping even after I replace the washer?

The valve seat—the metal surface the washer presses against—might be worn or rough. Over time, water can erode it, preventing a tight seal. You can smooth it with a valve seat dressing tool, or replace the entire cartridge if your tap uses one.

What’s the difference between a washer and an O-ring?

A washer is a flat rubber disc that seals the water flow when the tap is closed. An O-ring is a round rubber ring that seals around the cartridge or stem to prevent leaks around the handle. Both wear out and may need replacing.

Can I fix a dripping tap without turning off the water?

No. You must isolate the water supply to avoid a flood. Even if you think you can work quickly, water pressure will spray everywhere once you remove the handle or cartridge.

How do I know if my tap uses a washer or a ceramic disc?

Older taps (often with a cross-shaped handle) typically use washers. Modern mixer taps with a single lever usually have ceramic discs. If you see a cartridge with a ceramic disc inside, it’s not a washer type—clean the disc or replace the cartridge.

Is it worth fixing a dripping tap myself, or should I call a plumber?

If you’re comfortable with basic tools, fixing a washer-type tap is a simple DIY job. However, if your tap is a complex mixer or you’re unsure, a plumber can do it quickly. The cost of a plumber may be worth it if you lack the tools or confidence.

How often should I replace tap washers?

There’s no set schedule—washers wear out based on usage and water quality. If you notice a drip, it’s time to replace them. Regular maintenance every few years can prevent drips.

Fixing a dripping tap is a satisfying and practical skill. With the right tools and a careful approach, you can stop the drip, save water, and avoid the cost of a plumber. Remember to turn off the water first, take your time, and don’t over-tighten anything. If you run into trouble, the troubleshooting tips above should help you get back on track.