How to Clean Natural Stone: A Safe Guide

Natural stone surfaces—granite, marble, travertine, limestone, slate, and quartzite—add timeless beauty to kitchens, bathrooms, and entryways. But cleaning them incorrectly can dull the finish, etch the surface, or even cause permanent stains. This guide walks you through the safe, step-by-step process for cleaning natural stone, whether you’re tidying a countertop, a tile floor, or a shower surround. You’ll learn which supplies to use, which to avoid, and how to handle common mishaps without damaging your investment.

What You’ll Need

  • Mild dish soap (a few drops, not a squirt)
  • Warm water in a spray bottle or bucket
  • Soft microfiber cloths (several, to avoid cross-contamination)
  • Soft-bristle brush (for grout lines or textured surfaces)
  • Stone-specific cleaner (optional, but recommended for routine use)
  • Stone sealer (for maintenance, if your stone is porous)
  • Baking soda (for oil stains)
  • Hydrogen peroxide (for light-colored stone stains, use with caution)
  • Acetone (for stubborn adhesive or paint, use sparingly)
  • Plastic wrap and tape (for poultice application)

Step-by-Step

  1. Identify your stone type. Before you do anything, know whether your stone is calcareous (marble, limestone, travertine, onyx) or siliceous (granite, quartzite, slate, sandstone). Calcareous stones react with acids, so you must never use vinegar, lemon juice, or any acidic cleaner on them. Siliceous stones are more acid-resistant but still benefit from gentle care. If you’re unsure, test a small, hidden area with a drop of lemon juice—if it fizzes or dulls, it’s calcareous.
  2. Dust or vacuum first. Loose dirt and grit are the biggest enemies of natural stone. They act like sandpaper, scratching the surface when you wipe. Use a soft-bristle broom, a vacuum with a soft floor attachment, or a dry microfiber mop to remove dust and debris from floors. For countertops, a dry microfiber cloth works well.
  3. Prepare a gentle cleaning solution. For routine cleaning, mix a few drops of mild dish soap (like Dawn or a similar gentle formula) into a spray bottle or bucket of warm water. Avoid heavy-duty degreasers or anything with ammonia, bleach, or citrus. Alternatively, use a commercial stone cleaner that is pH-neutral and specifically labeled for your stone type.
  4. Dampen the surface, don’t soak it. Spray the solution onto the stone, but don’t flood it. Excess water can seep into unsealed stone and cause discoloration or damage. For floors, wring out your mop well—it should be damp, not dripping.
  5. Wipe gently in a circular motion. Use a soft microfiber cloth or mop. Avoid abrasive scrubbers, steel wool, or stiff brushes on the stone itself. For textured surfaces like slate or tumbled travertine, you can use a soft-bristle brush to work the cleaner into crevices, but be gentle.
  6. Rinse with clean water. Soap residue can dull the stone’s finish. After cleaning, go over the surface with a clean, damp cloth or mop using plain water to remove any soap film. For floors, you may need to go over them twice with clean water.
  7. Dry thoroughly. Water spots are more noticeable on dark or polished stone. Use a dry microfiber cloth to buff the surface dry. For floors, a dry mop or towel works. This also helps prevent mineral deposits from hard water.
  8. Address stains immediately. If you spill something, blot (don’t rub) with a soft cloth. For oil-based spills (cooking oil, butter), sprinkle baking soda on the spot, add a little water to make a paste, cover with plastic wrap, and let it sit for several hours or overnight. For organic stains (coffee, tea, fruit juice), use a paste of baking soda and hydrogen peroxide (for light stone) or baking soda and water (for dark stone). Apply the same way. Rinse and dry.
  9. Seal your stone (if recommended). Many stones, especially granite, marble, and travertine, benefit from a penetrating sealer. This doesn’t make the stone stain-proof, but it gives you time to clean spills. Reapply sealer according to the manufacturer’s instructions—typically once a year or every few years, depending on wear. Test a drop of water on the surface; if it beads up, the sealer is still effective. If it soaks in quickly, it’s time to reseal.
  10. Polish with a dry cloth for shine. For polished stone, a final buff with a clean, dry microfiber cloth will restore a glossy finish. For honed (matte) stone, buffing just removes streaks.

Common Mistakes

  • Using vinegar or lemon juice. This is the number one mistake. Acids etch calcareous stone, leaving dull spots that are difficult to remove. Even on granite, acids can break down the sealant over time.
  • Using abrasive cleaners or pads. Scouring powders, cream cleansers, and scrubby sponges scratch the surface, dulling the finish and creating places where dirt collects.
  • Leaving spills to sit. Natural stone is porous, even when sealed. A spill left overnight can penetrate and cause a permanent stain.
  • Using too much water. Soaking the stone can push water deep into the material, leading to discoloration, mold, or even cracks if it freezes.
  • Using ammonia or bleach. These can discolor the stone and damage the sealer.
  • Wiping in a back-and-forth motion. This can push dirt into the surface. Circular motions are gentler.
  • Ignoring the seal. Many homeowners never seal their stone, or seal it too often with the wrong product. Both are problematic.

Tips

  • Use coasters and trivets. Even a sealed countertop can stain if a hot pan sits on it for too long. Use trivets for hot items and coasters for glasses.
  • Wipe up spills immediately. The faster you act, the less likely a stain will set. Blot, don’t wipe.
  • Test any new cleaner on an inconspicuous area. Wait a few minutes, then check for dullness or discoloration.
  • Use a pH-neutral cleaner for daily use. You can buy a stone-specific cleaner, or make your own with a few drops of dish soap and water. Avoid anything labeled “all-purpose” unless it says pH-neutral.
  • For floors, place mats at entrances. This reduces the amount of grit tracked onto the stone.
  • For showers, use a squeegee. This removes hard water and soap scum before they dry and etch the stone.
  • Consider a stone-safe daily cleaner. Some brands offer spray cleaners that are safe for daily use and don’t require rinsing. Check the label.

Troubleshooting

What if my stone is already etched or dull? Etching (dull spots) from acid is a common issue. For a light etch, you can try a polishing powder specifically for stone (like a marble polishing powder). Mix it with water to a paste, apply with a damp cloth, and buff gently. For deeper etches, you may need a professional to re-polish the surface. Never attempt to use sandpaper or a sander yourself—you’ll likely make it worse.

What if there’s a stubborn stain? For oil stains, the baking soda poultice mentioned in Step 8 works well. For rust stains, use a commercial rust remover designed for stone—test it first. For organic stains, hydrogen peroxide can help, but be careful on dark stone as it may lighten it. If the stain persists, contact a stone restoration professional.

What if my stone has a white film or residue? This is often caused by soap scum or hard water. Try a stone-safe cleaner specifically formulated to break down soap scum. For hard water spots, a poultice of baking soda and water can help. Avoid using vinegar, which will etch the stone.

What if my stone is cracked or chipped? Small chips can be filled with a stone repair kit, available at hardware stores. Larger cracks should be handled by a professional to prevent further damage.

What if my sealer is worn off? If water soaks into the stone rather than beading up, it’s time to reseal. Clean the stone thoroughly, let it dry completely, then apply a stone sealer according to the manufacturer’s instructions. Usually, you apply it with a brush or cloth, let it sit for a few minutes, then wipe off the excess.

What if I accidentally used an acidic cleaner? Rinse the area immediately with water and dry it. If you see a dull spot, apply a stone polishing powder as described above. If the damage is severe, call a professional.

Frequently Asked Questions

Can I use vinegar to clean my granite countertops? No. Vinegar is acidic and will etch the surface of most natural stones, including granite (though granite is less reactive than marble). It can also break down the sealer, leaving your stone vulnerable to stains. Always use a pH-neutral cleaner.

How often should I seal my natural stone? It depends on the stone and how much use it gets. A simple test: drop a few drops of water on the surface. If they bead up, the sealer is still working. If they soak in quickly, it’s time to reseal. For heavily used countertops, this might be every few months; for less-used surfaces, once a year or less is common.

Can I use bleach to disinfect my stone? Bleach can discolor stone and damage the sealer. For disinfection, use a stone-safe disinfectant or a mixture of isopropyl alcohol and water (test on an inconspicuous area first). For everyday cleaning, warm water and dish soap are sufficient.

What’s the difference between a cleaner and a polish? A cleaner removes dirt and grime. A polish is a product that adds shine or a protective coating. Some polishes contain wax or silicone, which can build up over time. Use a polish only if your stone is polished and you want extra shine, and choose one that’s specifically for your stone type.

Can I use a steam mop on my stone floors? Steam mops can be risky. The high heat and moisture can damage the sealer and, over time, cause the stone to become dull. If you do use one, ensure it’s on a low setting and don’t let it sit in one spot. Better to use a damp mop.

What should I do if my stone has a dark ring from a glass? This is often a water ring, which can be caused by condensation. Try blotting with a dry cloth to see if it’s just surface moisture. If it persists, make a poultice of baking soda and water, apply it over the ring, cover with plastic wrap, and let it sit overnight. Rinse and dry. If it doesn’t come out, consult a professional.